background image

Water Softening

system

Safety Information

  . . . . . . . . . . . . . . . . . . . . 2

Specifications &Performance Claims

  . . . 3

About the Softener

  . . . . . . . . . . . . . . . . . . 4-6

Before you Start

  . . . . . . . . . . . . . . . . . . . . . . . 7

Installation Requirements

  . . . . . . . . . . 8-10

Installation Instructions

  . . . . . . . . . . . 11-15

Programming the Softener

  . . . . . . . . 16-20

Care and Cleaning

  . . . . . . . . . . . . . . . . . . . . 21

Routine Maintenance

  . . . . . . . . . . . . . . . . . 22

Before you call for Service

  . . . . . . . . . 23-26

Exploded View/Parts List

  . . . . . . . . . . 29-32

Warranty (U.S.)

  . . . . . . . . . . . . . . . . . . . . . . . 33

Warranty (Canada)

  . . . . . . . . . . . . . . . . . . . 34

7350846       49-50282-8    06-15 GE

GEAppliances.com

Write the model and serial 
numbers here:

Model #  ________________
Serial # _________________

To find these numbers, lift 
the cover and look on the rim 
below the control panel.

Model GXSF30V

Owner’s Manual & 

Installation Instructions

Water Softening  

System

Systems tested and certified by NSF International against 

NSF/ANSI Standard 44 for the chemical reduction claims 

specified on page 3, and certified to NSF/ANSI 372.

C

USA

R

Systems Tested and Certified by the Water Quality Association 

against CSA B483.1.

If you have any questions or concerns when installing or maintaining your 

water softener, call our toll free number at

 800-952-5039 (US)

 or 

866-777-7627 

(Canada),

 or visit 

www.geappliances.com

.  When you call, please be prepared 

to provide the model and serial number of your product.  This information can 

be found on the rating decal located on the rim under the salt cover.

Summary of Contents for GXSF30V











































































Reviews: