3 . 4 .
3 . 5 .
7 2
。
3 .
2 0 : 4 7 : 4 9
I D 3 . 1
I N T
1.800mL/min
↑
3 . 4 .
Footswitch
Trigger
：
3 .
2 0 : 4 7 : 4 9
I D 3 . 1
I N T
1.800mL/min
↑
3 . 5 .
Back Suction
：
1 8
°
3 . 6 .
Set Clock
：
1 6 : 4 6 : 1 5
3 .
2 0 : 4 7 : 4 9
I D 3 . 1
I N T
1.800mL/min
↑
3 . 6 .
Clock Setting
：
1 1
1 2
Running Interface
Running Interface
Running Interface
BT300-1F OPERATING MANUAL
BT300-1F OPERATING MANUAL
System Setting
System Setting
System Setting
Press the
Knob
Press the
Knob
Press the
Knob
Press the
knob and
then turn
the knob
Press the
knob and
then turn
the knob
Press the
knob and
then turn
the knob
Press the
knob and
then turn
the knob
Press the
knob and
then turn
the knob
Press the
knob and
then turn
the knob
3.4 Footswitch
Adjusting Knob
Adjusting Knob
Adjusting Knob
Exit Key
Start/Stop Key
Set footswitch working mode.
1.
Gated: The pump runs as long as the footswitch is pressed.
2.
Trigger: Press footswitch, the pump starts running; Press
footswitch again, the pump stops.
In “Footswitch” interface, press the
to enter
footswitch setting interface. Turn the
to select
the corresponding state. Press the
to save and
quit. Press the
to cancel the setting and return to
“Footswitch” interface.
Note:
The pump identifies the Longer Footswitch automatically. When
the pump connects the footswitch, the
on
operating panel is invalid no matter the remote control is on or off.
Footswitch
Gated Trigger
：
Turn the knob to
select working state
3.5 Back Suction
Adjusting Knob
Adjusting Knob
Adjusting Knob
Exit Key
In dispensing and filling state, to prevent the liquids drippage to
cause error when the filling stops, the pump will back-turn a back
suction angle to suck back the liquids. The back suction is the
same for each filling operation, it doesn't influence the filling
accuracy.
In “Back Suction” interface, press the
to enter
back suction angle setting interface. Turn the
to
adjust the back suction angle. Press the
to save
and quit. Press the
to cancel the setting and return to
“Back Suction” interface.
Back Suction
：
Turn the knob to adjust
angle
back suction
3.6 Clock Setting
Adjusting Knob
Adjusting Knob
Adjusting Knob
Exit Key
Set the time.
In “Time Setting” interface, press the
to enter
time setting interface. Set the hour, minute, second through press
and turn the
. Press the
to save
and quit. Press the
to cancel the setting and return to
“Time Setting” interface.
Press and turn the knob
to adjust time
3.7 Pump Head Selection
Adjusting Knob
Adjusting Knob
Adjusting Knob
Exit Key
Note:
Make sure the pump head corresponds to the setting of the menu.
In “Pump Head” interface, press the
to enter
pump head selection setting interface. Turn the
to
select the corresponding pump head. Press the
to
save and quit. Press the
to cancel the setting and return
to “Pump Head” interface.
After change the pump head, the default tubing is the minimal
diameter tubing used for this pump head.
