Running Interface
Switch on the power switch, initialize the pump first and then display
the running interface.
rpm State
b .
c .
d .
f .
e .
Flow Rates State
a .
b .
c .
d .
g .
e .
a .
h .
i .
a .
Filling and Dispensing State
3
4
2 0 : 4 7 : 4 9
3 0 0 R P M
I D 3 . 1
I N T
1 . 8 0 0 m L / m i n
2 0 : 4 7 : 4 9
I D 3 . 1
I N T
C l o c k：2 0 ： 4 7 ： 4 9
C o p y N o .：
2
D i s p V o l： 0 . 1 m L
Menu Frame Work
2 0 : 4 7 : 4 9
1.800mL/min
I D 3 . 1
I N T
1 .
Fill Setting
2 .
Calibration
3 .
System Setting
4 .
Control Mode
1 . 1 .
D i s p V o l
1 . 6 m L
a u s e T i m e
2 "
C o p y N o .
4
：
P
：
：
2 . 1 .
A c t V o l：
3 1 m L
D i s p T i m e： 2 7 "
P r e s s
t o b e g i n
3 . 1 .
TubingI.D.
：I D 2 . 4
3 . 2 .
Remote Contro
l
：
O n
3 . 3 .
Pump I.D.
： 1
3 . 4 .
F o o t s w i t c h：
T r i g g e r
3 . 5 .
B a c k S u c t i o n：
1 8
°
3 . 6 .
C l o c k S e t t i n g：
3 . 7 .
P u m p H e a d：
D G ( 6 - r o l l e r )
4 . 1 .
S e l e c t
R P M
F l o w
D i s p
Function Setting
↑
2 0 : 4 7 : 4 9
1.800mL/min
I D 3 . 1
I N T
1 .
2 .
3 .
4 .
a.
: Current time. Set in system setting menu.
b.
Direction: Show the direction of the pump.
c.
Tubing ID: Display the current tubing inner diameter.
d.
Start/Stop state: “Start” state displays “
”, “Stop” state displays“
”.
e.
Control Mode: “shut” means remote control is in “off” state. Remote
control is in “on” state, “INT” means the pump are controlled by
internal control; “V” means the pump are controlled by remote control
analog voltage signal; “mA” means the pump are controlled by remote
control analog current signal.
f.
rpm: Display current speed. Turning the
can increase
or decrease the speed.
g.
Flow Rate: Display current flow rate. Turning the
can
increase or decrease the flow rate.
h.
Copy No.: Display copy number in dispensing and filling state.
i.
: Display filling volume (one time) in dispensing and filling
state.
Adjusting Knob
Adjusting Knob
Clock
Disp Vol
BT300-1F OPERATING MANUAL
BT300-1F OPERATING MANUAL
Running Interface
Running Interface
Fill Setting
Calibration
Prompt:
Exit Key
The symbol of “
“ in the
interface means you can
press the
to
return
to
the
previous
interface.
In “Running Interface”, press the
to enter “Fill
Setting” interface. Turn the
to select 4 kinds of
Function Setting Interface.
Adjusting Knob
Adjusting Knob
Press the
Knob
Turn the
Knob
Turn the
Knob
Turn the
Knob
System Setting
Control Mode
