6
78112 Banzai_IM (20111910)
To Deflate:
1. Remove all users from the Aqua Blast Lagoon™.
2. Remove the ball from product and store them in a secure
place where it is out of reach of children.
3. Turn off and disconnect the water hose from the plug.
4. Before deflating, disconnect the anchor bags from the back
of the inflatable slide, drain the water from the bags, allow
to dry and properly store.
5. Drain water slide pool area by opening the water valve.
6. Dry water slide & wall.
7. Unplug the blower.
8. Disconnect the intake tube from the blower and place the
blower in a safe place.
9. Open the air release tube and allow the inflatable slide to
deflate completely. It should deflate on its own within 5
minutes. (Fig B1)
10. Remove the clear water tubing from the inflatable slide.
11. Remove the anchor stakes of the inflatable slide by pulling
on the head of the stakes. DO NOT pull on the slide
corners!
12. Allow the slide to dry completely before rolling up, which may take up to 48 hours.
Be sure the pool and slide are free of dirt, leaves, sand, etc. This will lengthen the life
of your slide.
13. Fold the inflatable slide in half, making sure that the release tube is parallel to the
fold. Fold it in half 2 more times, parallel to the first fold. (Fig B2-B3)
14. Roll the inflatable slide tightly starting from the end opposite the intake and release
tubes. (Fig B4-B5)
15. Roll the water slide tightly from one end to the other and avoid any creasing.
IMPORTANT:
Never store the Aqua Blast Lagoon™ when wet. Allow to dry before rolling up. Move the
slide everyday to prevent browning or damage to the lawn.
Follow all previous instructions each time you set up the slide.
Store slide in a secure place, away from children, to prevent suffocation.
Storage:
Slip the carrying bag over the rolled-up inflatable slide. Flip the bag and the slide over,
close the bag, and store the slide and the blower in a dry place. Store the water slide in a
secure place away from children to prevent suffocation. Never leave either the Aqua Blast
Lagoon™ or the blower outside when not in use. (Fig B6-B8)
To prevent mold and other damage to the slide, it is strongly advised to air out the
product with the blower motor to ensure it is completely dry before folding up for
storage.
To extend the life of the water spraying hose assembly, store it in a adequately ventilated
area. Do not store the water spraying hose assembly together with the slide.
Fig B1
Fig B2
Fig B3
Fig B4
Fig B5
Fig B6
Fig B7
Fig B8
Grounding Instructions
Maintenance of Aqua Blast Lagoon™
1. Check the slide at regular intervals for holes, tears or other damage. DO NOT use a damaged slide. Use of a
damaged slide could result in serious injury or death.
2. Check the water filled anchor bags at regular intervals for any signs of damage or deterioration. A damaged or
deteriorated water filled anchor bags could cause the slide to become unstable which would be a significant
safety hazard.
3. In addition to checking the product at a regular interval, be sure to complete a thorough check of the entire
product at the beginning of each season or series of use.
4. If any component of the product is damaged or deteriorated, discontinue use and contact the manufacturer.
5. Regularly check the condition of the ground stakes that hold the slide in place. Damage to or deterioration of
the stakes could result in the slide becoming unstable which could result in serious injury.
6. To keep the product clean, you can use a dry cloth or a cloth dampened with a neutral, non-inflammable,
nontoxic cleaning and sanitizing solution or pure water to wipe the surface of the slide or blower.
7. Use a dry cloth to clean the foot holes and remove debris after each play cycle. Make sure that there are no
water and debris in the pocket steps before storing.
This product should be grounded. In the event of an electrical short circuit, grounding reduces the risk of
electric shock by providing an escape wire for the electric current. This product is equipped with a cord
containing a grounding wire with an appropriate grounding plug. The plug must be plugged into an outlet
that is properly installed and grounded in accordance with all local codes and ordinances.
DANGER – Improper installation of the grounding plug can result in a risk of electric shock. If repair or
replacement of the cord or plug is necessary, do not connect the grounding wire to either flat blade
terminal. The wire with insulation having a green outer surface with or without yellow stripes is the ground-
ing wire.
Check with a qualified electrician or serviceman if the grounding instructions are not completely
understood or if in doubt as to whether the product is properly grounded. Do not modify the plug provided;
if it will not fit the outlet, have the proper outlet installed by a qualified electrician.
This product is for use on a nominal 120-V circuit, and has a grounding plug similar to the plug illustrated
in sketch below. A temporary adapter similar to the adapter illustrated in sketches B and C may be used to
connect this plug to a 2-pole receptacle as shown in sketch B when a properly grounded outlet is not
available.
The temporary adapter shall be used only until a properly grounded outlet is installed by a qualified electri-
cian. The green colored rigid ear, lug, or similar part extending from the adapter must be connected to a
permanent ground such as a properly grounded outlet box cover. Whenever the adapter is used, it must be
held in place by a metal screw.
Grounding methods
