manualshive.com logo in svg

Banner TCER, Setup Manual

Share
Download
Banner TCER Setup Manual Download Page 11

11

To add additional doors to an occupancy monitoring system, order one of each model listed below (900 MHz or 2.4 GHz).

Emitter-Receiver Pair

Indicator

Operator Interface

Battery

Battery

900 MHz

DX80N9X2W-DIR

TL70DXN9GRQ-INOUTIKIT

DX80N9DSTS

BWA-BATT-013 

C Battery

BWA-BATT-001 

D Batteries

2.4 GHz

DX80N2X2W-DIR-NB

TL70DXN2GRQ-INOUTIKIT

DX80N2DSTS-NB

The 900 MHz models are commonly used in the United States. The 2.4 GHz models are required in the EU and many other countries and 
the 

-NB

 in the model number indicates it ships without batteries.

Additional Mounting Options

BWA-BK-020 Magnet Mount

•  Used with the Direct Select Operator Interface or DXM Controller
•  Includes two 80-lb pull rare-earth magnet mounts 

and two #10-32 × 1 inch screw mounts 

•  Compatible with several other mounting brackets 
•  31.75 mm (1.25 inch) diameter
•  No fasteners included

LMB30LP

•  Used with the TL70 Wireless Indicator Light
•  Low profile 
•  30 mm mounting hole 
•  300 series stainless steel 
•  No fasteners included

Optional Accessories

Warning Indicator Segment

SG-TL70-Y

 

•  Used with the TL70 Wireless Indicator Light
•  Yellow indicator for Warning indication

View Dashboard and Set Parameters

After Banner CDS has created the site and detected the DXM Controller, click on 

Go to Dashboard

 (Go to Dashboard). The 

 (Dashboard) panel appears and indicates the metrics of the Occupancy Solution Kit. 

The data on this dashboard will include a historical indication of the Occupancy of the area and a means of updating the 
Occupancy Limit and Occupancy Warning parameters.

4

SXI-LTE-001

•  Used with DXM Controller
•  Allows for Cellular Connectivity to the Banner CDS platform

Cellular Modem

BWA-HW-OSK-001

•  Hardware packet used for mounting the Emitter-

Receiver Directional Sensor Pair

•  Stainless steel L-bracket
•  Zinc-plated steel washer
•  Delrin locknut

Receivers
DX80N9X2W-DIRR

•  900 MHz 
•  Includes batteries

DX80N2X2W-DIRR-NB

•  2.4 GHz
•  No batteries included

Emitters
DX80NxX2W-DIRE

•  Includes batteries

DX80NxX2W-DIRE-NB

•  No batteries included

Replacement Sensors

Summary of Contents for TCER













Reviews:

No comments

Brands by name

Popular brands

Load more brands