background image

I/O #

Modbus Holding Register

I/O Type

I/O Range

Holding Register Rep-
resentation

Terminal

Block Labels

Gateway

Any Node

Min. Value Max. Val-

ue

Min.
(Dec.)

Max. (Dec.)

9

9

9 + (Node# × 16)

Discrete OUT 1

0

1

0

1

DO1

10

10

10 + (Node# × 16)

Discrete OUT 2

0

1

0

1

DO2

11

11

11 + (Node# × 16)

Discrete OUT 3

0

1

0

1

DO3

12

12

12 + (Node# × 16)

Discrete OUT 4

0

1

0

1

DO4

...

15

15

15 + (Node# × 16)

Control Message

16

16

16 + (Node# × 16)

Reserved

Specifications

Radio and General

Range

900 MHz: Up to 4.8 kilometers (3 miles)

Transmit Power

900 MHz: 21 dBm conducted

900 MHz Compliance (150 mW Radios)

FCC ID TGUDX80 - This device complies with FCC
Part 15, Subpart C, 15.247
IC: 7044A-DX8009

Spread Spectrum Technology

FHSS (Frequency Hopping Spread Spectrum)

Link Timeout

Gateway: Configurable
Node: Defined by Gateway

Radio range is with the 2 dB antenna that ships with the product.
High-gain antennas are available, but the range depends on the
environment and line of sight. To determine the range of your wire-
less network, perform a Site Survey.

Power

Requirements: +10 to 30V dc (Outside the USA: +12 to
24V dc, ±10%). (See UL section below for any applica-
ble UL specifications)
Consumption: Less than 1.4 W (60 mA) at 24V dc

Housing

Polycarbonate housing and rotary dial cover; polyester
labels; EDPM rubber cover gasket; nitrile rubber, non-
sulphur cured button covers
Weight: 0.26 kg (0.57 lbs)
Mounting: #10 or M5 (SS M5 hardware included)
Max. Tightening Torque: 0.56 N·m (5 lbf·in)

Antenna Connection

Ext. Reverse Polarity SMA, 50 Ohms
Max Tightening Torque: 0.45 N·m (4 lbf·in)

Interface

Indicators: Two bi-color LEDs
Buttons: Two
Display: Six character LCD

Wiring Access

Four PG-7, One 1/2-inch NPT, One 5-pin Euro-style
male connector

For European applications, power the DX80 from a Limited Power
Source as defined in EN 60950-1.

Inputs and Outputs

Discrete Inputs

Rating: 3 mA max current at 30V dc
Sample Rate: 62.5 milliseconds
Report Rate: On change of state

Discrete Input ON Condition

PNP: Greater than 8V
NPN: Less than 0.7V

Discrete Outputs

Update Rate: 125 milliseconds
ON Condition: Supply minus 2V
OFF Condition: Less than 2V

SureCross DX80 Node

 

 

P/N 131293 Rev. F

www.bannerengineering.com - tel: 763-544-3164

5

Summary of Contents for SureCross DX80








Reviews: