NOTE: Cabled hookups are shown. QD hookups are functionally identical.
Specifications
Supply Voltage and Current
10 V dc to 30 V dc (10% max. ripple); supply current (exclusive of load
current):
Emitters: 25 mA
Receivers: 20 mA
Polarized Retroreflective: 30 mA
Fixed-Field: 35 mA
Supply Protection Circuitry
Protected against reverse polarity and transient voltages
Output Configuration
SPDT solid-state dc switch; NPN (current sinking) or PNP (current
sourcing) outputs, depending on model
Light Operate: N.O. (normally open) output conducts when sensor
sees its own (or the emitter’s) modulated light
Dark Operate: N.C. (normally closed) output conducts when the
sensor sees dark; the N.C. output may be wired as a normally open
marginal signal alarm output, depending upon hookup to power supply
Environmental Rating
Leakproof design rated NEMA 6P, DIN 40050 (IEC IP69K)
Construction
PBT polyester housing; polycarbonate (opposed-mode) or acrylic lens
Required Overcurrent Protection
WARNING: Electrical connections must be
made by qualified personnel in accordance
with local and national electrical codes and
regulations.
Overcurrent protection is required to be provided by end product
application per the supplied table.
Overcurrent protection may be provided with external fusing or via
Current Limiting, Class 2 Power Supply.
Supply wiring leads < 24 AWG shall not be spliced.
For additional product support, go to
http://
www.bannerengineering.com
.
Supply Wiring (AWG)
Required Overcurrent Protection (Amps)
20
5.0
22
3.0
24
2.0
26
1.0
28
0.8
30
0.5
Output Rating
150 mA maximum (each) in standard hookup. When wired for alarm
output, the total load may not exceed 150 mA.
OFF-state leakage current: < 1 µA at 30 V dc
ON-state saturation voltage: < 1 V at 10 mA dc; < 1.5 V at 150 mA
dc
Output Protection Circuitry
Protected against false pulse on power-up and continuous overload or
short circuit of outputs
Output Response Time
Opposed mode: 3 ms ON, 1.5 ms OFF
Retro, Fixed-Field and Diffuse: 3 ms ON and OFF
NOTE: 100 ms delay on power-up; outputs
do not conduct during this time
Repeatability
Opposed mode: 375
μ
s
Retro, Fixed-Field and Diffuse: 750
μ
s
Repeatability and response are independent of signal strength
Indicators
Two LEDs (Green and Amber)
Green ON steady: power to sensor is ON
Green flashing: output is overloaded
Amber ON steady: N.O. output is conducting
Amber flashing: excess gain marginal (1 to 1.5 times) in light
condition
Connections
2 m (6.5 ft) or 9 m (29.5 ft) attached cable or 4-pin Euro-style quick-
disconnect fitting
Operating Conditions
Temperature:
−
40 °C to +70 °C (
−
40 °F to +158 °F)
Humidity: 90% at +50 °C maximum relative humidity (non-
condensing)
Vibration and Mechanical Shock
All models meet Mil. Std. 202F requirements. Method 201A (Vibration;
frequency 10 Hz to 60 Hz, max., double amplitude 0.06 inch
acceleration 10G). Method 213B conditions H&I. (Shock: 75G with unit
operating; 100G for non-operation)
Certifications
Banner Engineering Corp. Limited Warranty
Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp.
will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty
period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION,
ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE
OF DEALING OR TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE
LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL,
CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER
ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product
previously manufactured by Banner Engineering Corp.
Q25 DC Sensors
www.bannerengineering.com - Tel: +1-763-544-3164
