Specifications
Supply Voltage and Current
10 V dc to 30 V dc (10% maximum ripple) at less than 45 mA,
exclusive of load
Supply Protection Circuitry
Protected against reverse polarity and transient voltages
Adjustments
Push-button TEACH mode sensitivity setting; remote TEACH mode
input is provided
Indicators
Two LEDs: amber and bi-color green/red
Construction
Reinforced thermoplastic polyester housing, totally encapsulated, o-
ring seal, acrylic lenses, and stainless steel screws.
Required Overcurrent Protection
WARNING: Electrical connections must be made by
qualified personnel in accordance with local and
national electrical codes and regulations.
Overcurrent protection is required to be provided by end product
application per the supplied table.
Overcurrent protection may be provided with external fusing or via
Current Limiting, Class 2 Power Supply.
Supply wiring leads < 24 AWG shall not be spliced.
For additional product support, go to
.
Supply Wiring (AWG)
Required Overcurrent Protection (Amps)
20
5.0
22
3.0
24
2.0
26
1.0
28
0.8
30
0.5
Connections
PVC-jacketed 5-conductor 2 m (6.5 ft) or 9 m (30 ft) unterminated
cable, or 5-pin Euro-style quick-disconnect (QD) fitting are available.
QD cables are ordered separately.
Application Notes
The first condition presented during TEACH mode becomes the output
ON condition.
Output Configuration
Bipolar: One current sourcing (PNP) and one current sinking (NPN)
open-collector transistor
Output Rating
150 mA maximum each output at 25° C, derated to 100 mA at 70° C
(derate
≈
1 mA per °C)
Off-state leakage current: less than 5
μ
A at 30 V dc
ON-state saturation current: less than 1 V at 10 mA; less than 1.5 V at
150 mA
Output Protection Circuitry
Protected against false pulse on power-up and continuous overload or
short-circuit of outputs
Output Response Time
Sensors will respond to either a “light” or a “dark” signal of 500
microseconds or longer duration, 1 kHz max.
NOTE: 1 second delay on power-up; outputs do not
conduct during this time.
Repeatability
100 microseconds (all models)
Rating
Meets NEMA standards 1, 2, 3, 3S, 4, 4X, 6, 12, and 13; IEC IP67
Operating Conditions
Temperature: –20° to +70° C (–4° to +158° F)
Max. Relative Humidity: 90% at 50° C (non-condensing)
Troubleshooting
If the MINI-BEAM Expert’s Power LED alternately flashes red/green, this indicates a microprocessor memory error. To clear
the error, re-teach the sensor or cycle the power ON and OFF and re-teach the sensor. If this does not solve the problem,
or if it occurs frequently, replace the sensor.
Banner Engineering Corp. Limited Warranty
Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp.
will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty
period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION,
ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE
OF DEALING OR TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE
LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL,
CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER
ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product
previously manufactured by Banner Engineering Corp.
Copyright Notice
Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the product is identified as not
intended for such purposes will void the product warranty. Any modifications to this product without prior express approval by Banner Engineering Corp will void the product
warranties. All specifications published in this document are subject to change; Banner reserves the right to modify product specifications or update documentation at any
time. For the most recent version of any documentation, refer to:
.
©
Banner Engineering Corp. All rights reserved.
MINI-BEAM Expert Series
www.bannerengineering.com - Tel: +1-763-544-3164
