background image

Introduction

The BeoAmp 2 amplifier is a highly compact and light-weight solution with 
audiophile sound quality. Thanks to the class D technology, the amplifier has very 

low heat dissipation and is therefore perfectly suitable for installation in a rack 
system.

This amplifier is very powerful considering its compact size with 2 channels, each 
capable of delivering 150W/8Ω. Furthermore, it features universal mains for world-
wide use and standby functionality compliant with ErP 2013 which specifies 

standby power consumption below 0.5W.

The amplifier is 1U high for easy rack installation. The amplifier’s width of 200 mm 
means that two amplifiers can sit next to each other in a 19” rack with a stabilizer 

between them. It is possible to mount rack ears either on the side or on the top of 

the amplifier, enabling the amplifier to be installed on any flat surface, such as a 
wall or a ceiling (see rack possibilities drawings on page 9).

Features

Ultra-compact enclosure (2 pcs BeoAmp 2 fits in a 1U rack).

Extremely low weight - up to seven times lighter than similar products.

Up to 2 x 150W channels of audiophile sound quality.

Very low power consumption and heat dissipation thanks to efficient ICEpower 

Class-D technology.

Comprehensive protection keeps the music playing and your quality costs down.

Removable rack ears and feet.

Summary of Contents for 9699













Reviews: