background image

Warning

Please adhere to all the following safety instructions before use:

Important Safety Instructions

1.  Read these instructions.
2.  Keep these instructions.
3.  Heed all warnings.
4.  Follow all instructions.
5.  Do not use this apparatus near water.
6.  Clean only with dry cloth.
7.  Do not block any ventilation openings. Install in accordance with the 

manufacturer’s instructions.

8.  Do not install near any heat sources such as radiators, heat registers, stoves, or 

other apparatus (including amplifiers) that produce heat.

9.  Do not defeat the safety purpose of the polarized or grounding-type plug. A 

polarized plug has two blades with one wider than the other. A grounding type 
plug has two blades and a third grounding prong. The wide blade or the third 

prong are provided for your safety. If the provided plug does not fit into your 

outlet, consult an electrician for replacement of the obsolete outlet.

10.  Protect the power cord from being walked on or pinched particularly at plugs, 

convenience receptacles, and the point where they exit from the apparatus.

11. 

Only use attachments/accessories specified by the manufacturer.

12. 

Use only with the cart, stand, tripod, bracket, or table specified by the 

manufacturer, or sold with the apparatus. 

When a cart is used, use caution when moving the cart/apparatus combination to 
avoid injury from tip-over. 

13.  Unplug this apparatus during lightning storms or when unused for long periods of 

time.

14. 

Refer all servicing to qualified service personnel. Servicing is required when the 

apparatus has been damaged in any way, such as power-supply cord or plug is 
damaged, liquid has been spilled or objects have fallen into the apparatus, the 
apparatus has been exposed to rain or moisture, does not operate normally, or has 
been dropped.

Additional Safety Information

15.  The appliance coupler is used as the disconnect device and shall remain readily 

operable.

16.  The ground pin of the mains plug must not be removed due to the danger of 

electric shock. If a wall outlet with protective earth is not available, an electrician 
should be contacted.

17.  The supplied plug and mains cord are specially designed for the product. Do not 

change the plug. If the mains cord is damaged, you must purchase a new one 

from the retailer as per specified by the manufacturer.

18. 

No naked flame sources, such as lighted candles, should be placed on the 

apparatus.

Summary of Contents for 9699













Reviews: