background image

29

FPLMP138

FPLMP138

In

 more 

detail

 . . .

Recoil starter

The recoil starter handle (

24

) is positioned at the top of the engine. 

1.  Pull the brake clutch (

3

) towards the upper handle bar (

1

) and hold it in position 

(Fig. 

12

). 

2.  Pull the recoil starter handle (

24

) lightly until you feel resistance then pull it rapidly.  

Do it repeatedly until the engine starts (Fig. 

13

). 

3.  During operation rest the recoil starter handle (

24

) onto a hook (

23

) located on the 

right-hand side of the upper handle bar (

1

) (Fig. 

14

).

13

14

24

23

1

WARNING!

 Never twist the starter cord around your hand! Only pull on the 

recoil starter handle (

24

)!

WARNING!

 Do not suddenly release the recoil starter handle (

24

)! Allow the 

rope to return slowly and in a controlled manner each time it is pulled!

Grass catcher

WARNING!

 Always attach the grass catcher (

22

) when using this product - 

danger of flying objects! Always carry the grass catcher by its handle (

22b

).

Emptying

WARNING!

 Before removing the grass catcher (

22

) stop the engine and wait 

until the blade (

26

) comes to a complete stop.

Empty the grass catcher (

22

) frequently during use. Do not wait until it is full. We 

recommend emptying when it is 

90

% full.

NOTE:

 A full grass catcher (

22

)

 

reduces the performance of the product.

1.  Lift the rear deflector guard (

21

) and hold it in place. 

2.  Lift the grass catcher hooks (

22a

) off the rods and place the grass catcher (

22

) on 

the ground.

3.  Remove the grass clippings from the discharge chute (

28

) into the grass catcher (

22

). 

Use a proper tool such as a brush.

WARNING!

 Never use your hands or feet to remove grass clippings from the 

discharge chute (

28

)!

4.  Empty the grass clippings onto a compost heap. 

5.  Re-fit the grass catcher hooks (

22a

) onto the rods. 

Grass catcher inspection

During use the grass catcher (

22

) material is subjected to normal wear and tear. An 

excessively worn grass bag may allow the objects to be thrown towards the operator. 

Replace a worn grass bag to prevent possible injury. 

Cutting height adjustment

WARNING!

 Before adjusting the cutting height, stop the engine and wait until 

the blade (

26

) comes to a complete stop.

This product can be adjusted to 7 different height settings. The cutting height depends on 

the kind of lawn and its actual height. When mowing high grass, start with the maximum 

cutting height and make a second cut with lower cutting height. New or thick grass may 

require a higher cutting height and a narrower cutting path. 

1.  Pull the lever for cutting height adjustment (

18

) towards the wheel (

16

) (Fig. 

15

, step 

1

), 

and then move it forward or backward to the desired cutting height (Fig. 

15

, step 

2

). 

2.  Release the lever (

18

) and ensure it engages into place properly (Fig. 

15, 

step 

3

). 

NOTE:

 If you are not sure what cutting height should be selected, start with a 

maximum height and check the appearance of the lawn after mowing a small 

area. Adjust the setting if necessary.

Product functions

3663602423287-GB-V04.indd   29

27/9/2018   14:54

Summary of Contents for FPLMP138

















































Reviews: