background image

Bandit

32

Copyright 4/21

MODELS 2550/2550T

CONSULT THE ENGINE  MANUFACTURER’S 

 MANUAL FOR SPECIFIC CONTROLS,  OPERATION, & 

 MAINTENANCE FOR TYPICAL ENGINES

1.  Ignition Switch: 

Turn the ignition switch key clockwise one stop (on position) to turn the electrical system 

on. The key should remain in the on  position while the engine is running. Turn the key fully clockwise (start 

position) this will start the engine. To shut off  the engine, return the key to the off  position.

2.  Ignition Switch With Preheat: 

The typical diesel engine may have a preheat system to assist in  starting 

the engine during cold weather. To activate the preheat system, continue to hold the ignition key in the 

preheat position for 15 to 20 seconds, then attempt to start the engine. If the engine fails to start within 

15 seconds, return the key to the preheat position, hold 10 seconds, and try starting again.

3.  Choke (if equipped): 

Some gasoline engines may have a choke, pull the choke lever out to choke the 

engine. Push the choke lever in for normal engine operations.

4.  Throttle Adjustment (if equipped): 

Some engines may have a knob or a handle for the throttle  adjustment. 

Typically you would pull the knob out, or turn the handle to increase the engine R.P.M.’s. To decrease you 

would push in the knob or turn the handle the opposite way.

5. 

“Bandit” Lever Lock Cable Throttle System (if equipped): 

The Bandit throttle system has (2)  positions, 

HIGH and LOW. Engine R.P.M. is controlled by moving the lever from one position to the other.

6.  Push Button Or Electric Throttle System (if equipped): 

Some engines may have a push button or electric 

throttle adjustment. Engine R.P.M. is controlled by pushing a button or switch to raise or lower the R.P.M.

7.  Alternator Warning Light: 

This light will glow when the  alternator is not charging, or when the ignition 

switch is turned on and the engine is not running.

8.  Oil Pressure Warning Light: 

This light will glow when the oil pressure is to low, or when the ignition 

switch is turned on and the engine is not running.

9.  Engine Temperature Warning Light: 

This light will glow when the engine, or engine coolant, is above 

normal operating temperature. If this occurs allow the engine temperature to cool down. If the engine is 

overheating because of a loss of coolant, or a broken fan belt, shut the engine off   immediately.

CONTROLS

NOTICE

  Most engines have an automatic low oil pressure shut down device, but some engines do not. Expensive 

damage may occur if the engine oil level and condition is not checked daily. Follow all maintenance procedures 

specifi ed by the engine manufacturer’s manual. Check the fuel level daily, running out and repriming is time 

consuming. Do not over fi ll the tank, there must be expansion space in the top of the tank. Inspect hoses, 

fi ttings, lines, tanks, etc. for any oil, fuel, engine coolant, etc. leaks daily. Repair or replace any damaged or 

leaking components.

TYPICAL GASOLINE 

ENGINES

BANDIT  THROTTLE   SYSTEM

TYPICAL DIESEL ENGINES

PUSH BUTTON OR  ELECTRIC 

THROTTLE  SYSTEM

BANDIT 

CONTROLS

Summary of Contents for 2550



































































































Reviews: