background image

2.3 Ah V-05 Installation Instructions

Battery Backup Kit

 

BATTERY BACKUP KIT 2.3Ah V-05 - ORDER NO. 61914

ITEM

DESCRIPTION

QTY

1

BATTERIES COVER

1

2

BATTERIES SUPPORT

1

3

BATTERY 12V SEC 12-2.2 AGM TYPE

2

4

BATTERY COUPLING WIRE - ESV24

1

5

BATTERY HARNESS

1

6

PAN HEAD SCREW W/WASHER M4x8

2

7

CABLE CLAMP ACC-1.5 (3/16”)

1

8

CHARGER BOARD SBY-3 V-1.00

1

9

CHARGER HARNESS SBY-3

1

10

SBY BATTERY HARNESS

1

PACK #1 (SECTIONAL DOOR OPENERS)

11

HEX STANDOFF M4

2

12

PAN HEAD SCREW W/WASHER M4x8

4

13

THRUSS SER HD SCREW “S” RoHS M4x8

2

14

TAPTITE SCREW “P” M4 X 8

3

15

PCB SUPPORT 76X27

1

PACK #2 (ROLLER DOOR OPENERS)

16

TAPTITE SCREW “P” M4x8

4

17

TAPTITE SCREW “P” M4x10

2

18

CABLE CLAMP ACC-2.5 (5/16”)

1

BATTERY BACKUP KIT SBC-02 - ORDER NO. 90188

ITEM

DESCRIPTION

QTY

19

BATTERY CHARGER BOX ASSEMBLY

1

20

CHARGER BOARD SBY-3 V-1.00

1

ACCESSORY PACK 

21

TIE MOUNT CM-13 (ADHIESIVE)

4

22

CABLE TIE 4” GT-100M

4

23

BRACKETS GE 44 621

4

24

SCREW “P” M3.5 X 13 FOR GW 44 621

4

Garage Door Openers

Swing Gate Openers

BATTERY BACKUP KIT ESV24 - ORDER NO. 61912

ITEM

DESCRIPTION

QTY

25

BATTERY CP1223H 12V 2.3H

2

26

CHARGER BOARD SBY-3 V-1.00

1

27

BATTERY COUPLING WIRE - ESV24

1

28

BATTERY HARNESS

1

29

TAPTITE SCREW “P” M3 X 8

4

Sliding Gate Openers

Important Safety Instructions

 

WARNING!

• 

DO NOT 

short the output of batteries. 

Serious personal injury

 and/or property damage 

can result from failure to follow this warning

• 

During charging and discharging cycles the lead-acid batteries may release explosive 

gases.  Ensure that the area around the batteries is well ventilated

• 

Take care not to allow any metal objects to make contact with the positive and negative 

terminals. This will short circuit the battery causing sparks and possible damage to the 

battery, or even cause an explosion.

 

ELECTROCUTION!

• 

The battery box unit should be installed away from sprinkler systems.

• 

DO NOT

 immerse in water or spray directly with a hose or other device.

• 

Disconnect the power cord from mains power before making any repairs or removing 
covers.

CAUTION:

Muscular strain

• 

Practice correct lifting techniques 

Fall from ladder

• 

Ensure ladder is the correct type for job.

• 

Ensure ladder is on flat ground.

• 

Ensure user has 3 points of contact while on ladder.

Burns

• 

DO NOT

 handle damaged or leaking batteries

• 

Wear appropriate protective clothing and avoid touching your eyes after working with 
batteries.

• 

The battery backup kit contains sealed lead-acid batteries that must be disposed of 
properly at the end of their useful life.

Doc # 160036_03
Part #  13402
Released 10/10/16

Summary of Contents for V-05









Reviews: