B&D Smart Pro SDO-9V3, Installation Instructions Manual

Page: 16 / 29

16 Smart Pro, Smart & Secure installation instructions
15. Coding a Transmitter
BUTTON
TRANSMITTER
FUNCTION
Open / Stop / Close HOLD
PET (Pedestrian) Mode HOLD
Open HOLD
Light HOLD HOLD
Vacation Mode HOLD HOLD
Aux Output HOLD HOLD
* The button coded for open only function can close the door
if you hold the button for 4 seconds, when the door is fully open..
MAIN LIGHT & BEEPER TRANSMITTER STATUS
ON + 2 x Button added
OFF + 2 x Button removed
x 2, then OFF + 2 x Remote control deleted
x 4, then OFF + 4 x Memory full
15.1 Storing the Transmitter Code
Light Status Battery
Solid OK
Flashing Replace
No light Replace
3 . 0 C O D I N G A R E M O T E C O N T R O L
S T E P O N E
The opener can only be operated from remote
controllers that have been programmed into its
memory. Up to 64 remotes can be programmed.
Battery Type: 1 x CR2032.
W A R N I N G ! : The battery is hazardous and must
be kept out of reach of children. The battery can
cause severe or fatal injuries within 2 hours or
less if swallowed or placed inside any part of the
body. If you suspect the battery has been
swallowed or placed inside any part of the body,
SEEK IMMEDIATE medical attention.
S T E P T W O
S T E P T H R E E
Switch power on and
remove controls cover
till remote
LED lit
Press
repeatedly
HOLD
Opener
flashes &
beeps
HOLD for 3 sec
HOLD for 3 sec
RELEASE
Release both
buttons
S T E P F O U R
S T E P F I V E
Press to test
tip
S T E P O N E
4 . 0 C H A N G I N G A B A T T E R Y
HOLD
Check Light
Status Table
S T E P T W O
tip
Use screwdriver
to remove
screws and
open
S T E P T H R E E
Use non-metallic
object to push
out.
C O D I N G R E M O T E F R O M T H E O P E N E R
S T E P O N E S T E P T W O
Take a pre-coded
remote and press the
button to duplicate
R E M O T E L Y C O D I N G A R E M O T E C O N T R O L
Remotely coding works when you have a
pre-coded remote control and are in range of the
opener.
tip
Use a pen,
HOLD for 2 sec
the middle button
through the
coding hole
S T E P T H R E E
Opener flashes & beeps
HOLD for 3 sec
HOLD for 3 sec
RELEASE
Take new
remote
RELEASE
S T E P F I V E
Press to test
Opener stops flashing &
beeping
Then refit controls cover
15.2 Remotely Coding Transmitters
Light Status Battery
Solid OK
Flashing Replace
No light Replace
3 . 0 C O D I N G A R E M O T E C O N T R O L
S T E P O N E
The opener can only be operated from remote
controllers that have been programmed into its
memory. Up to 64 remotes can be programmed.
Battery Type: 1 x CR2032.
W A R N I N G ! : The battery is hazardous and must
be kept out of reach of children. The battery can
cause severe or fatal injuries within 2 hours or
less if swallowed or placed inside any part of the
body. If you suspect the battery has been
swallowed or placed inside any part of the body,
SEEK IMMEDIATE medical attention.
S T E P T W O
S T E P T H R E E
Switch power on and
remove controls cover
till remote
LED lit
Press
repeatedly
HOLD
Opener
flashes &
beeps
HOLD for 3 sec
HOLD for 3 sec
RELEASE
Release both
buttons
S T E P F O U R
S T E P F I V E
Press to test
tip
S T E P O N E
4 . 0 C H A N G I N G A B A T T E R Y
HOLD
Check Light
Status Table
S T E P T W O
tip
Use screwdriver
to remove
screws and
open
S T E P T H R E E
Use non-metallic
object to push
out.
C O D I N G R E M O T E F R O M T H E O P E N E R
S T E P O N E S T E P T W O
Take a pre-coded
remote and press the
button to duplicate
R E M O T E L Y C O D I N G A R E M O T E C O N T R O L
Remotely coding works when you have a
pre-coded remote control and are in range of the
opener.
tip
Use a pen,
HOLD for 2 sec
the middle button
through the
coding hole
S T E P T H R E E
Opener flashes & beeps
HOLD for 3 sec
HOLD for 3 sec
RELEASE
Take new
remote
RELEASE
S T E P F I V E
Press to test
Opener stops flashing &
beeping
Then refit controls cover
NOTE: To code other transmitter functions, at STEP THREE
refer to below table of buttons to press.
NOTE: The opener will flash and beep during coding,
refer to below table for status indication..
Remote code set is disabled when:
• powered by battery backup
• the service indicator is active
• when the door is indicating that it was
prevented from closing by a P.E beam
being blocked
tip