B&D EconoLift Installation Instructions Manual Download

Page: 15 / 20

PARAMETERS

DOOR STATUS INDICATORS

DOOR OPENER STATE

OPEN LED

GREEN

CLOSE LED

RED

DOOR STATUS

LED YELLOW

BEEPER

OPEN

OPENING

FLASHING

CLOSING

FLASHING

DOOR TRAVEL STOPPED

FLASHING

DOOR OBSTRUCTED WHEN OPENING

FLASHING

DOOR OBSTRUCTED WHEN CLOSING

FLASHING

BEEPS WHILE

DOOR IS MOVING

OPENER OVERLOADED

ALTERNATING

FLASHES

ALTERNATING

FLASHES

MAINS POWER INTERRUPTED

RAPID

FLASHES

BUTTONS

FUNCTION

OPERATE

Opens/Stops/Closes the door

Door Code

Codes a transmitter button for OPERATE function

Force Margin Set + Plus (+)

Increases the obstruction force margin setting

Force Margin Set + Minus (-)

Decreases the obstruction force margin setting

Force Margin Set (then) Set

Reloads the factory set default obstruction force margin setting

Close for 6 Secs

Clears the door limits set positions. Limits then need to be reset.

Set (then power on) & hold until all LEDs are off

Deletes control parameters excluding transmitter storage memory.

Door Code (then power on) & hold until all LEDs are off

Deletes all transmitter stored in memory.

Set for 2 sec.

Re-initialises the Opener to re-calculate force margins

Summary of Contents for EconoLift





















Search results

Summary of Contents for EconoLift

Reviews:

Related manuals for EconoLift

Brands by name

Popular brands

B&D EconoLift, Installation Instructions Manual

Search results

Summary of Contents for EconoLift

Reviews:

Related manuals for EconoLift

Brands by name

Popular brands