![background image](http://html1.mh-extra.com/html/bandd/controll-a-door-secure-sdo-6/controll-a-door-secure-sdo-6_installation-instructions_3076230002.webp)
b&d group office locations
Head Office
6-8 Fiveways Blvd, Keysborough 3173
Phone (03) 9791 0200
New South Wales
34 Marigold St, Revesby 2212
Phone (02) 9722 5555
Queensland
17 Oasis Court, Clontarf 4019
Phone (07) 3883 0200
Victoria
147-153 Canterbury Rd, Kilsyth 3137
Phone (03) 9237 7766
South Australia
23 Frederick Rd, Royal Park 5014
Phone (08) 8440 4747
Western Australia
96 Mulgul Rd, Malaga 6090
Phone (08) 9247 8777
International/Export
34 Marigold St, Revesby 2212
Phone +61 (0)2 9722 5555
New Zealand
46 Braeburn Dr, hornby, Chch 8082
Phone +64 (0)3 384 5145
www.bnd.com.au
Prefixed trademarks are the property of B&D Australia Pty Ltd. B&D Doors & Openers
is a division of B&D Australia Pty Ltd. ABN 25 010 473 971. © 2016 B&D Australia Pty Ltd.
2
Smart Phone Control Kit -
Installation instructions
your representative is
Warranty
Smart Hub Set Up
Mounting the Hub
a. Determine whether you are going to wall mount the hub.
i. If hub is to be placed on bench, simply connect to power supply
2
, turn on and proceed to installing the Transceiver.
ii. If hub is to be wall mounted follow steps below.
b. To wall mount - Use wall bracket
3
as template to mark where to drill
holes. Pre-drill holes.
i. For plaster walls - insert (2) two Plastic wall plugs
4
into holes,
place wall bracket over holes and affix with (2) two self tapping
screws
5
.
ii. For brick walls - place wall bracket
3
over holes and affix with (2)
two self tapping screws
5
.
c. Slide the hub over the bracket.
d. Connect the power supply
2
and turn on.
1
3
5
6
6
SDO-8
ACC
This device must be connected to power at all times.
DO NOT disconnect power after setup.
Mounting the Transceiver to the Opener
a. Disconnect the power supply to the opener.
b. Remove the screw holding cover from the
opener.
c. Connect the 4 pin harness
7
to ACC on the
control board then connect to the wireless
basestation module
6
.
d. Place the module into the pocket as shown
and refit the cover.
e. Download the B&D App and follow the
instructions in the App to setup new smart hub.
f. Use a programmed remote and run the door
through a few cycles which will update the
unit with the details of the transceiver module.
SDO-6
Refer to our websites for full warranty details;
www.bnd.com.au
WARRANTY
ACCESSORIES
1 year
If you are a consumer under the Australian Consumer Law, our goods come with guarantees that cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You
are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
This warranty certificate and other statements contained in this document or other ATA documents given to you do not exclude, restrict or modify the application of
all or any of the provisions of the Australian Consumer Law.
Subject to your non-excludable rights under the Australian Consumer Law, ATA expressly excludes any liability for consequential loss, incidental or indirect damages
(including but not limited to damages for loss of business profits, business interruption and loss of business information) due to a defect of the Product. In particular,
any loss or damage caused to other equipment or accessories used with the product or any loss resulting from a delay in repair is excluded to the extent permitted
by law.
ACC