manualshive.com logo in svg

B&D Controll-A-Door P Diamond SDO-2v2, Instruction Manual, Page: 3 / 38

Share
Download
B&D Controll-A-Door P Diamond SDO-2v2 Instruction Manual Download Page 3

Safety Rules

Please read these important safety rules

These safety alert symbols indicate a personal safety or property damage 
instruction exists. READ THESE INSTRUCTIONS CAREFULLY. 

This automatic garage door opener is designed and tested to offer safe 
service provided it is installed and operated in strict accordance with the 
following safety rules. Failure to comply with the following instructions may 
result in death, serious personal injury or property damage.

CAUTION:

 If your garage has no pedestrian entrance 

door, an emergency access device should be installed. 

This accessory allows manual operation of the garage 

door from outside in case of power failure.

Position the Garage Door Opener so that the power plug 

is accessible when inserted into the power outlet (EN 
60335-1).

This opener should be installed in accordance with relevant 

Australian Standards.

Do not allow children to play with door controls.

Keep transmitters away from children. 

Watch the moving door and keep people away until the 

door is completely opened or closed.

Activate the opener only when the garage door is in full 

view, free of obstructions and with the opener properly 

adjusted.

Keep the garage door balanced. Sticking or binding 

doors must be repaired. Garage doors, door springs, 

brackets and their hardware are under extreme tension and 
can cause serious personal injury. Do not attempt any garage 
door adjustment. Do not use if repair or adjustment is needed. 
Call for professional garage door service.

Install the optional wall transmitter in a location where the 

garage door is visible, but out of the reach of children at 

a height of at least 1.5m. 

Disconnect electric power to the garage door opener 

before removing covers.

Doors requiring over 400N of force to move must have 

Safety Beams 

fi

 tted.

Do not wear rings, watches or loose clothing while 

installing or servicing a garage door opener.

This opener is not suitable for commercial, industrial 

or common entry applications.

To avoid serious personal injury from entanglement, 

remove all unnecessary ropes or chains and disable 

any equipment such as locks which are not needed for 
powered operation.

Installation and wiring must be in compliance with 

your local building and electrical codes. Connect 

the power cord only to properly earthed mains. If an 
extension lead must be used, make sure it is a 3-core lead 
and approved to 7 amp capacity.

If the power cord is damaged, it must be replaced 

by the manufacturer, its service agent or a similarly 

quali

fi

 ed person in order to avoid a hazard.

When using optional Auto-Close mode, a Safety 

Beam (Part No 062734) must be 

fi

 tted  correctly 

and tested at regular intervals. Extreme caution is 
recommended when using Auto-Close mode. All safety 
rules must be followed.

This opener is a plug in domestic appliance and is 

designed for indoor use only. It must be installed in 

a dry position that is protected from the weather. 

The opener is not intended for use by young children 

or in

fi

 rm persons without supervision.

B&D Doors to the extent that such may be lawfully excluded hereby expressly disclaims all conditions or warranties, statutory or otherwise which may be implied by laws as 
conditions or warranties of purchase of a B&D Garage Door Opener. B&D Doors hereby further expressly excludes all or any liability for any injury, damage, cost, expense or claim 
whatsoever suffered by any person as a result whether directly or indirectly from failure to install the B&D Garage Door Opener in accordance with these installation instructions.

WARNING! It is vital for the safety of 

persons to follow all instructions. Save 

these instructions.

Diamond PD Power Drive : Instruction Manual

© Copyright 2012 B&D Doors

3

Controll-A-Door

®

 P

 

Diamond SDO-2v2

 

Instruction Manual

Summary of Contents for Controll-A-Door P Diamond SDO-2v2







































Reviews:

No comments