B&C Technologies HP series Installation And Operation Manual Download Page 28 | Manualshive

Page: 28 / 39

background image

Wear Eye and hand protection when handling chemicals. Always avoid
direct contact with raw chemicals. Read the manufacturer’s directions for
accidental contact before handling chemicals. Ensure that an eye-rinse
facility and an emergency shower are within easy reach. Check at regular
intervals for chemical leaks.

26

Installation

External Chemical Supplies

The following procedures must be observed
when connecting any chemical injector to
the washer-extractor. See the figure for a
typical supply injection system setup.
Undiluted chemicals dripping can damage
the machine. Therefore, all chemicals
supply dispenser pumps must be mounted

below the washer’s injection point. All
dispenser tubing should also run below the
injection point. Loops do not prevent drips
if these instructions are not followed. Failure
to follow these instructions could damage
the machine and void the warranty.

Supply

Connection

Chemical
Dispenser
Pump

PCV Pipe

«
...
26
27
28
29
30
...
»

Summary of Contents for HP series








































Reviews:

No comments

Related manuals for HP series

Brand: GE Pages: 2

Brand: GE Pages: 108

Brand: Hansa Pages: 2

Brand: Hansa Pages: 2

Brand: Jackson Pages: 80

Brand: Jackson MSC Pages: 42

Brand: Kärcher Pages: 32

Brand: Bartscher Pages: 18

Brand: Indesit Pages: 16

Brand: magic clean Pages: 56

Brand: Vax Pages: 16

Brand: IKEA Pages: 104

Brand: Supra Pages: 24

Brand: Samsung Pages: 80

Brand: Samsung Pages: 136

Brand: Samsung Pages: 210

Brand: Samsung Pages: 234

WA52M7755A series

Brand: Samsung Pages: 236

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands