B&B Electronics Zlinx ZP Series Manual Download Page 49 | Manualshive

Page: 49 / 49

background image

Manual Documentation Number: ZPXXx-XXXXx-MR-0812

49

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 –

www.bb-elec.com

B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 –

www.bb-europe.com

TR (Transmit Error Count)
Command

<Diagnostics> Read number of
retransmit failures. The
number of retransmit errors is
incremented each time a
packet is not acknowledged
within the number of
retransmits specified by the
RR (Retries) parameter. It
therefore counts the number of packets that were not successfully received and have
been dropped.

The TR parameter is not non-volatile and therefore is reset to zero each time the
module is reset.

TT (Streaming Limit)
Command

<Networking & Security>
Set/Read the number of bytes
that can be sent out before a
random delay is issued. TT
Command is used to simulate
full-duplex behavior.

If a module is sending a continuous stream of RF data, a delay is inserted
(transmission is stopped, allowing other modules time to transmit (once it sends
number of bytes specified by TT Command). Inserted random delay lasts between 1
& „RN + 1‟ delay slots, where each delay slot lasts 38 ms.

VR (Firmware Version)
Command

<Diagnostics> Read the
Firmware Version of the
module.

WR (Write) Command

<(Special)> WR Command
writes configurable parameters
to the module‟s non-volatile memory (Parameter values remain in the module‟s
memory until overwritten by future use of WR Command).

If changes are made without writing them to non-volatile memory, the module reverts
back to previously saved parameters the next time the module is powered-on.

AT Command: ATTR

Binary Command: 0x1B (27 decimal)

Parameter Range: 0

– 0xFFFF

Default Parameter Value: 0

Number of bytes returned: 2

Related Commands: RR (Retries)

Minimum Firmware Version Required: 4.22

AT Command: ATTT

Binary Command: 0x1A (26 decimal)

Parameter Range: 0

– 0xFFFF [bytes]

Default Parameter Value: 0xFFFF (65535d)

Number of bytes returned: 2

Related Commands: RN (Delay Slots)

Minimum Firmware Version Required: 4.22

AT Command: ATVR

Binary Command: 0x14 (20 decimal)

Parameter Range: 0

– 0xFFFF [read-only]

Number of bytes returned: 2

AT Command: ATWR

Binary Command: 0x08

«
...
47
48
49

Summary of Contents for Zlinx ZP Series


















































Reviews:

No comments

Related manuals for Zlinx ZP Series

Brand: 4RF Pages: 12

Brand: 4RF Pages: 12

Brand: 4RF Pages: 2

Brand: 4RF Pages: 2

Brand: Morphy Richards Pages: 2

Brand: ICP DAS USA Pages: 38

Brand: Akai Pages: 12

Brand: Raymarine Pages: 47

ROCKET 2AC PRISM

Brand: Ubiquiti Pages: 28

Brand: Radio Shack Pages: 10

Brand: Hamilton Beach Pages: 10

Brand: Technika Pages: 20

Brand: Zodiac Pages: 74

CX789 - Digital AM/FM/NOAA Radio

Brand: Coby Pages: 6

Brand: Teleorigin Pages: 35

Bearcat 980 SSB

Brand: Uniden Pages: 24

Brand: Albrecht Pages: 13

Brand: Matsutec Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands