B&B Electronics Zlinx ZP Series Manual Download Page 32 | Manualshive

Page: 32 / 49

background image

32

Manual Documentation Number: ZPXXx-XXXXx-XR-0812

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 –

www.bb-elec.com

B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 –

www.bb-europe.com

CB (Connection Duration
Timeout) Command

<Networking & Security>
Set/Read the maximum amount
of time an exclusive
connection between a base and
remote module in a point-to-
multipoint network is sustained.
The remote module will
disconnect when this timeout
expires.

CC (Command Sequence
Character) Command

<Command Mode Options> CC
Command is used to set the
ASCII character to be used
between Guard Times of the AT
Command Mode Sequence
(BT+ CC + AT). The AT
Command Mode Sequence
activates AT Command Mode
(from Idle Mode).

Refer to the AT Commands section to view the default AT Command Mode
sequence.

CD (DO3 Configuration)
Command

<Serial Interfacing> CD
Command is used to redefine the
behavior of the DO3 (Data Output
3)/RX LED line.

CE (Connection Inactivity
Timeout) Command

<Networking & Security>
Set/Read the duration of
inactivity that will cause a break
in a connection between
modules. The base module
will disconnect when no payload
has been transferred for the time
specified by the CE parameter.

Binary Command: 0x33 (51 decimal)

Parameter Range:

0x01

– 0xFFFF

[x 100 milliseconds]

Default Parameter Value: 0x28 (4d seconds)

Number of bytes returned: 2

Related Commands: CE (Connection Inactivity
Timeout), DC (Disconnect), MD (RF Mode)

Minimum Firmware Version Required: 4.30

AT Command: ATCC

Binary Command: 0x13 (19 decimal)

Parameter Range:

0x20

– 0x7F

Default Parameter Value: 0x2B (ASCII “+” sign)

Number of bytes returned: 1

Related Commands: AT (Guard Time After), BT
(Guard Time Before)

AT Command: ATCD

Binary Command: 0x28 (40 decimal)

Parameter Range: 0

– 4

Parameter

Configuration

0

RX LED

1

Default high

2

Default low

3

(reserved)

4

Assert only when packet

addressed to module sent

Default Parameter Value: 0

Number of bytes returned: 1

Minimum Firmware Version Required: 4.2B

AT Command: ATCE

Binary Command: 0x34 (52 decimal)

Parameter Range:

0

– 0xFFFF

[x 10 milliseconds]

Default Parameter Value: 0x64 (1d second)

Number of bytes returned: 2

Related Commands: CB ( Connection Duration
Timeout), DC (Disconnect), MD (RF Mode)

Minimum Firmware Version Required: 4.30

«
...
30
31
32
33
34
...
»

Summary of Contents for Zlinx ZP Series


















































Reviews:

No comments

Related manuals for Zlinx ZP Series

Brand: iRZ Pages: 20

Brand: Xoro Pages: 16

Brand: Olympia Pages: 32

Bearcat UBC3500XLT

Brand: Uniden Pages: 94

Brand: Insignia Pages: 24

Brand: Albrecht Pages: 52

Brand: Marine Pages: 5

Brand: Raymarine Pages: 76

Brand: VisionTek Pages: 6

Brand: Sangean Pages: 116

Brand: Ubiquiti Pages: 28

Brand: THOMSON Pages: 10

Brand: Paradyne Pages: 60

USB ADSL Modem UAM700

Brand: Abocom Pages: 15

Brand: Microsoft Pages: 37

Bearcat 980 SSB

Brand: Uniden Pages: 24

Brand: Vertex Standard Pages: 116

Brand: Hitachi Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands