B&B Electronics EIR618-2SFP-T User Manual Download

Page: 82 / 116

Manual Documentation Number: EIR618-2SFP-T_5107m

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com

B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com

Aggregator Information

Displays static trunk group information.

Port Trunk—Aggregator setting interface (two ports are added to the left field with LACP

disable)

Port Trunk – Aggregator Information interface

State Activity

After setting up the LACP aggregator, port state activity can be configured.

Mark the port and click

Apply

. The port state activity will change to

Active

Passive

depending on its previous state.

Active:

The port automatically sends LACP protocol packets.

Passive:

The port responds only if it receives LACP protocol packets

from the opposite device.

Summary of Contents for EIR618-2SFP-T





















































































































Search results

Summary of Contents for EIR618-2SFP-T

Reviews:

Related manuals for EIR618-2SFP-T

Brands by name

Popular brands

B&B Electronics EIR618-2SFP-T, User Manual

Search results

Summary of Contents for EIR618-2SFP-T

Reviews:

Related manuals for EIR618-2SFP-T

Brands by name

Popular brands