BALZER Field Floater 1325 Extension User Manual Download Page 70

Page: 70 / 83

Lubrication & Maintenance

Lubrication Vertical Auger

Five (5) grease fittings are located on the auger folding
hinge. These should be greased every day. Pump grease
until old grease is visible.

The bearing located at the end of the vertical auger
should get 1 to 2 careful pumps of grease every day of
constant use.

BALZER

INC.

Excessive pressure while applying grease can be
harmful to the bearing seals.

Apply never seize to shaft that goes through pillow
block bearing once every 40 hours.

Apply grease to fitting located on the bottom end of
auger folding cylinder. This should be greased every
day. Pump grease until old grease is visible.

Summary of Contents for Field Floater 1325 Extension




















































































Search results

Summary of Contents for Field Floater 1325 Extension

Reviews:

Related manuals for Field Floater 1325 Extension

Brands by name

Popular brands

BALZER Field Floater 1325 Extension, User Manual

Search results

Summary of Contents for Field Floater 1325 Extension

Reviews:

Related manuals for Field Floater 1325 Extension

Brands by name

Popular brands