BALZER Field Floater 1325 Extension User Manual Download Page 54

Page: 54 / 83

Operation

BALZER

INC.

Model 640M Calibration

Calibration Instructions for Model 640M Indicator (kg, 8 weigh bar)

The following calibration instructions are for setting up an Avery Weigh-Tronix Model 640M for weighing in Kg and an
eight weigh bar Balzer Grain Cart. If this procedure doesn't get results within 1% then field calibration must be performed.

From the Gross Mode, press and hold the HOLD/MENU
Key for three beeps, then release…

SET.PAS is displayed

Use the Numeric Entry Procedure and enter in 640

640 is displayed

Press the PRINT/SELECT key…

640 is displayed
with all display annunicators lit

Press the PRINT/SELECT key…

CONFIG is displayed

Press the PRINT/SELECT key…

Current Configuration # is shown

Use the Numeric Entry Procedure to enter the following
Configuration Code: 098394

098394 is shown

Press the PRINT/SELECT key…

CONFIG is shown

Press the MENU key once…

CUSTOM is shown

Press the PRINT/SELECT key…

Current Custom # is shown

10.

Use the Numeric Entry Procedure to enter the following
custom code number: 033690

033690 is shown

11.

Press the PRINT/SELECT key…

CUSTOM is shown

12.

Press the G/N key twice, busy is shown

returns to Gross weighing mode

Summary of Contents for Field Floater 1325 Extension




















































































Search results

Summary of Contents for Field Floater 1325 Extension

Reviews:

Related manuals for Field Floater 1325 Extension

Brands by name

Popular brands

BALZER Field Floater 1325 Extension, User Manual

Search results

Summary of Contents for Field Floater 1325 Extension

Reviews:

Related manuals for Field Floater 1325 Extension

Brands by name

Popular brands