BTL5-A/C/E/G1_-M_ _ _ _-B/Z-NEX-S32/KA_ _
Micropulse Linear Transducer - Rod Style
14
english
Ignition Class "n"
Repeatability
Voltage
0.3 mV
Current
0.6 µA
Minimum
0.05 mm
Sampling rate f
Standard
= 2 kHz
Non-linearity
Nom. length < 500 mm > 500 mm
in µm
±100
±0.02 % FS
Temperature coefficient
Voltage output:
[150 µV/K + (5 ppm/K * P * V/NL)] *
∆
T
Current output:
[0,6 µA/K + (10 ppm/K * P * I/NL)] *
∆
T
V
= output voltage range in [V]
I
= output current range in [mA]
NL = nominal length in [mm]
∆
T = temperature coefficient in [K]
P
= magnet position in [mm]
Shock
100 g/6 ms
per IEC 60068-2-27
1
Continuous shock 100 g/2 ms
per IEC 60068-2-29
1
Vibration
12 g, 10 to 2000 Hz
per IEC 60068-2-6
1
(take care to avoid inherent reso-
nances of protective tube)
Pressure
up to 600 bar
when installed in a
hydraulic cylinder
1
Individual specifications as per
Balluff factory standard
12.1
Dimensions, weights,
ambient conditions
Nominal length
< 4000 mm
Dimensions
➥
➥
➥
➥
➥
Fig. 3-2
Weight
approx. 2 kg/m
Housing
anodized aluminum
Pressure tube Stainless steel 1.4571
diameter
10.2 mm
wall thickness
2 mm
e-modulus
approx. 200 kN/mm
2
Mounting thread M18×1.5 or
3/4"-16UNF
Operating temp.
–20 °C to +60 °C
Humidity
< 90 %, non-dewing
Protection rating
per IEC 60529
IP 67
with connector attached
12.2
Supply voltage (external)
Regulated supply voltage
BTL5-_1_-... DC 20 to 28 V
Ripple
< 0.5 V
pp
Current draw
< 150 mA
Inrush
< 3 A/0.5 ms
Polarity reversal protection built-in
Overvoltage protection
Transzorb diodes
Electric strength
GND to housing 500 V
12.3
Outputs
BTL5-A...
Output voltage
0...10/10...0 V
Load current
< 5 mA
Ripple
< 5 mV
BTL5-G...
Output voltage
–10...10/10... –10 V
Load current
< 5 mA
Ripple
< 5 mV
BTL5-C...
Output current
0...20/20...0 mA
Load resistance
< 500 Ohm
BTL5-E...
Output current
4...20/20...4 mA
Load resistance
< 500 Ohm
12.4
Connection to controller
Analog interface:
With S32 connector for shielded
cable (max. length, see "Wiring"),
diameter 6 to 8 mm, or with integral
cable (5 m long)
12.5
Included in shipment
Transducer
➥
➥
➥
➥
➥
Fig. 3-2
Calibration device
➥
➥
➥
➥
➥
Fig. 7-1
12.6
Magnets
(order separately)
Magnets BTL-P-1013-4R,
BTL-P-1013-4S, BTL-P-1012-4R
Dimensions
➥
➥
➥
➥
➥
Fig. 3-4
Weight
approx. 10 g
Housing
anodized aluminum
Operating temp.
–40 °C to +85 °C
Included:
8 mm spacer
Material POM (polyoxymethylene)
12.7
Accessories (optional)
Connectors
➥
➥
➥
➥
➥
Fig. 4-3
12.8
Mounting nuts
(order separately)
Mounting nuts M18*1,5
BTL-A-FK01-E-M18X1,5
Mounting nuts 3/4"-16UNF
BTL-A-FK01-E-3/4"-16UNF
No
. 830 046 EN • F16; specifications subject to changes •
Replaces edition 0606
.
12
Technical Data
Typical values at DC 24 V, room temperature and BTL with nominal length of 500 mm. Ready for operation at once,
full accuracy after warm-up. With magnet BTL-P-1013-4R, BTL-P-1013-4S or BTL-P-1012-4R:
Emission tests:
RF Emission
EN 55011
Noise immunity tests:
Static electricity (ESD)
EN 61000-4-2
Severity level 3
Electromagnetic fields (RFI)
EN 61000-4-3
Severity level 3
Fast transients (Burst)
EN 61000-4-4
Severity level 3
Surge
EN 61000-4-5
Severity level 2
Line-induced noise induced by
high-frequency fields
EN 61000-4-6
Severity level 3
Magnetic fields
EN 61000-4-8
Severity level 4
The CE Mark verifies
that our products meet
the requirements of the
current EMC Directive
as well as the ATEX Directive.
Compliance is confirmed with the
enclosed CE declaration of conformity.
The transducer meets the requirements
of the following product standard:
EN 61326-2-3 (noise immunity
and emission)
The CE Mark verifies that our
products meet the requirements
of EC Directive.
