background image

Consolidated 1511 Series Safety Valve Instruction Manual 

 |  5

© 2020 Baker Hughes Company. All rights reserved.

DANGER — Immediate 

hazards which WILL result 

in severe personal injury or 

death.

WARNING — Hazards or 

unsafe practices which 

COULD result in severe 

personal injury or death.

CAUTION — Hazards or 

unsafe practices which 

COULD result in minor 

personal injury.

ATTENTION — Hazards 

or unsafe practices which 

COULD result in product or 

property damage.

1

2

3

4

If and when required, appropriate safety labels have been included in the 

rectangular margin blocks throughout this manual. Safety labels are vertically 

oriented rectangles as shown in the 

representative examples

 (below), consisting 

of three panels encircled by a narrow border. The panels can contain four 

messages that communicate:
•  The level of hazard seriousness
•  The nature of the hazard
•  The consequence of human, or product, interaction with the hazard.
•  The instructions, if necessary, on how to avoid the hazard.

The top panel of the format contains a signal word (DANGER, WARNING, 

CAUTION or ATTENTION) which communicates the level of hazard 

seriousness.

The center panel contains a pictorial which communicates the nature of the 

hazard, and the possible consequence of human or product interaction with 

the hazard. In some instances of human hazards the pictorial may depict what 

preventive measures to take, such as wearing protective equipment.

The bottom panel may contain an instruction message on how to avoid the 

hazard. In the case of human hazard, this message may also contain a more 

precise definition of the hazard, and the consequences of human interaction 

with the hazard, than can be communicated solely by the pictorial.

I.  Product Safety Sign and Label System

Do not remove bolts 

if pressure in line, as 

this will result in severe 

personal injury or 

death.

Know all valve 

exhaust/leakage points 

to avoid possible 

severe personal injury 

or death.

Wear necessary 

protective equipment to 

prevent possible injury.

Handle valve carefully. 

Do not drop or strike.

1

2

3

4

Summary of Contents for Consolidated 1511 Series

































Reviews: