background image

OVERVIEW

I-E96-435A   

1 - 1

SECTION 1 - INTRODUCTION

OVERVIEW

The RTD Analog Input Termination Module (NIAI03) is used by
the RTD Analog Slave Module (IMASM03/04). Each NIAI03 can
input eight three-wire RTD signals from field equipment. The
signals pass through the slave module to the Analog Master
Module (IMAMM03). This manual explains the purpose, setup,
handling precautions and steps to install the NIAI03 termina-
tion module. 

INTENDED USER

System engineers and technicians should read this manual
before installing and using the termination module (TM). Put
the module into operation only after reading and understand-
ing this instruction. Refer to the 

Table of Contents

 to find the

information. Refer to the 

HOW TO USE THIS MANUAL

 

entry in

this section to get started.

MODULE DESCRIPTION

The NIAI03 is a single printed circuit board that uses one slot
in a Termination Module Mounting Unit (NTMU01/02). The
termination module (TM) has one card edge connector that
connects to the slave module through a cable. The terminal
blocks for field wiring are on the TM. The NIAI03 handles up to
eight three-wire RTD inputs for the IMASM03/04. Figure 

1-1

shows an application example for the NIAI03.

FEATURES

The design of the NIAI03, as with all INFI 90 devices, allows for
flexibility in creating a process management system. Refer to
the 

NOMENCLATURE

 entry of this section for the list of devices

that can be used with the TM in an INFI 90 system.

A standard factory-wired cable connects the TM to the
slave module.

Connect I/O wires on terminals at the front edge of the TM.

Each TM fits in a standard termination mounting unit.

Field wire termination for eight three-wire RTD inputs.

Input channel transient and surge protection.

RTD input signal routing to the IMASM03/04.

Summary of Contents for Infi 90 NIAI03

























Reviews: