BAGRAM STX-1795 Manual Download Page 9 | Manualshive

Page: 9 / 18

background image

9

www.stairslight.com

The relays used to separate 230V circuit from

the controller may be of any type. We recommend

the relays to be mounted on T-35 bus, the same as

the controller. Their use helps with the installation.

Photo to the left shows our product STP-4811 — a

set of two relays in a single-rail case T-35. This set

makes it possible to separate 230 V voltage coming

simultaneously from two motion sensors.

Installation diagram: 110-230V motion sensors connected to the controller

Set of two relays STP-4811

«
...
7
8
9
10
11
...
»

Summary of Contents for STX-1795



















Reviews:

No comments

Related manuals for STX-1795

Brand: ABB Pages: 139

Brand: ABB Pages: 28

Brand: ABB Pages: 59

Brand: D-Link Pages: 40

ClubSport Wheel Base V2

Brand: FANATEC Pages: 39

Brand: KAR-TECH Pages: 28

Brand: 2M Technology Pages: 17

Brand: 2iB Pages: 5

Go!Control Panel

Brand: 2gig Technologies Pages: 78

Brand: Neets Pages: 12

Brand: National Instruments Pages: 24

Brand: Unitech Pages: 55

Brand: S&C Pages: 8

Z3-DM8107-SDI-RPS

Brand: Z3 Technology Pages: 73

Brand: Z-Wave Pages: 14

Brand: Z-Wave.Me Pages: 4

Brand: Gardena Pages: 236

Brand: TWR Lighting Pages: 49

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands