background image

IMPORTANT SAFETY INFORMATION

IT IS VERY IMPORTANT TO READ AND FOLLOW THE

SAFETY PRECAUTIONS BEFORE ASSEMBLY AND

DURING THE USE OF THE PRODUCT.

GENERAL INFORMATION

1. The Grill Shack is designed primarily to extend the outdoor use of your home.

DO NOT USE STRUCTURE AS FOLLOW:

- As safety barrier to prevent unsupervised access to pools, hot tubs, spas or ponds.

- As load bearing support for other structures, buildings or heavy objects.

- As a support for swings or hammocks. If you wish to suspend products to the structure, ensure

that the total weight of articles does not exceed 15 pounds. Suspend nothing from the structure in

case of strong winds.

2. Wood is not flame retardant and has the potential of burning. Do not place any type of heat 

source on/under the structure or within 5 ft of the unit including, but not limited to, a barbecue, 

chiminea or fire pits. Consult the user’s manual of these items for safe distances from combustible

materials.

3. This structure is a four-season product.

4. Permanent structures may require a building permit. It is the consumer’s responsibility to comply

with building rules, regulations/zoning restrictions orders or any other regional restrictions and

obtain the required permits before purchasing this product and installing it.

5. Always install the product on a solid level surface or platform capable of supporting the 

structure. Minimum 3.5" concrete slab or 12" deep footing. With wood deck, the structure must 

attach to the framing of the deck and not to the decking planks. Structure can not be attached to 

pavers or stepping stones.

6. This product must be anchored to either wood or concrete using the appropriate fasteners and

anchors for the chosen flooring. (Hardware included)

7. Check for underground utilities before digging or driving stakes into the ground.

8. Keep all children and pets away from assembly area.

9. Do not assemble the product in days of wind or rain.

10. Wear gloves to avoid injury from possible sharp edges of individual elements before assembly.

11. During installation, follow all safety warnings provided with your tools and use OSHA approved               

safety glasses.

12. A minimum of two people is required to install safely.

13. To avoid damages to the product its parts and surroundings, use the proper tools. Do not use 

the product as a support. The use of a ladder(s) is required.

Wood components are manufactured with North American Timbers. As your Grill Shack acclimates to 

its new environment, natural characteristics of the wood can show in the form of checks (cracks) and 

weathering in the lumber.This is normal and it will not affect the structural integrity of your structure 

and is not covered under warranty.

Annual application of oil-based stain is important and will help reduce weathering and checks.

2

Summary of Contents for GRILL SHACK



























Reviews: