background image

S
T
E

P

 

16 

Step 16:  Place the plastic protective caps (Part S) over the heads and the nuts on 
the chair frame as shown in photo. 

CONGRATULATIONS!  Your Hanging Lounger is now complete. 

Please always follow the safety instruction and use common sense when using the Hanging 
Lounger.   

The Hanging Lounger is intended for a single user at one time and has a weight capacity of 268 
lbs.  NEVER EXCEED THE WEIGHT CAPACITY. 

Care should always be taken when using your Hanging Lounger but especially when using the 
lounger for the first time.   

The suspended seat of the Hanging Lounger allows it to move freely, so be very cautious when 
getting into and out of the Hanging Lounger. 

Never allow small children to use the Hanging Lounger unattended. 

Always inspect the Hanging Lounger before each use to assure everything is properly attached 
and secure for use. 

Always use the Hanging Lounger on a level surface. 

FOR YOUR SAFETY 

For spots on the pad, gently wash spotted area with a mild soap and water solution. 

The Hanging Lounger has a powder coated outdoor finish on the metal parts.  However, over time 
and use, scratches may develop on the metal surfaces.  To avoid excessive rust, wipe these areas 
of moisture. 

Before storing the Hanging Lounger, wipe thoroughly to wipe off moisture and dirt. 

Store the Hanging Lounger in a dry location. 

Care 

Summary of Contents for 272-3265










Reviews: