manualshive.com logo in svg

Backflow Direct Deringer 20, Maintenance Instructions Manual, Page: 18 / 20

Share
Download
Backflow Direct Deringer 20 Maintenance Instructions Manual Download Page 18

4X”- 6” Deringer 20/30 Maintenance Instructions

BD-INST-02030  |  Rev C  |  12/22/2015  |  Copyright 2011 Backflow Direct, LLC

Close Test Cocks and Double Check all Closing/Sealing Mechanisms

1. Using the Backflow Direct Test Cock Wrench or a small 

adjustable wrench close Main Test Cocks Number 1, 2 
and 3 (A). (Test Cock is closed when wrench flats on 
stem are perpendicular to water flow through Test Cock)

2. Using a #2 Flathead Screwdriver Close Bypass Test Cock 

Number 1 and 2 (B). (Test Cock is closed when 
screwdriver slot on stem is perpendicular to water flow 
through Test Cock)

3.

Use the “T” handles to open bypass Ball Valve Number 1 
(C) and then open bypass Ball Valve Number 2 (D). (Ball 
Valve is open when “T” handle is parallel to water flow 
through Ball Valve)

4. Double check to be certain of the following: 

•

All Cover Bolts are Tightened (E)

•

Bypass Check Valve Cover is Tightened (F)

•

Bypass Meter Coupling Nuts are Tightened (G)

A

A

B

BD-INST-4X2030  |  Rev A  |  09/06/2019  |  Copyright 2011 Backflow Direct, LLC

B

FLOW

Page 18 of 20

D

E

C

G

F

Summary of Contents for Deringer 20





















Reviews:

No comments