Backflow Direct Deringer 20 Maintenance Instructions Manual Download Page 13 | Manualshive

Page: 13 / 20

Backflow Direct Deringer 20 Maintenance Instructions Manual Download Page 13

4X”- 6” Deringer 20/30 Maintenance Instructions

BD-INST-02030 | Rev C | 12/22/2015 | Copyright 2011 Backflow Direct, LLC

Maintenance of Second Dual-Action Check Module

BD-INST-4X2030 | Rev A | 09/06/2019 | Copyright 2011 Backflow Direct, LLC

A

B

E

D

F

D

G

Page 13 of 20

1. Use a #2 Philips Head Screwdriver to remove Tower

Screws (A) from the Second Check Seat (B) The Double
Torsion Spring is captured and does not need to be
retained during maintenance.

2. After removing the Tower Screws (A) Examine the

Elastomer Disk (D) and Check Seat (E) for fouling or
damage.

3. Should Elastomer Disk (D) need replacement unscrew

Disk Retainer Screws (F) and remove Disk Retainer (G).
Carefully remove and replace Elastomer Disk (D).
When replacing Elastomer Disk (D) be certain that no
air, water or debris is trapped in the Clapper (H) cavity
behind the Elastomer Disk (D).

4. Reverse the order of the above instructions to reassemble check.

• Elastomer Disk must be flat in Clapper (H) cavity before

tightening Disk Retainer Screws (F).

• Do not cross thread Disk Retaining Screws (F).

«
...
11
12
13
14
15
...
»

Summary of Contents for Deringer 20





















Reviews:

No comments