background image

 

 

Seite 8/8 

 Bachler austria 

Gmbh

, Industriebedarf für Umwelt, Heizung & Solar, Dr.-F.-X.-Mayr-Str.299, 

A-8962 Gröbming, Tel.: 03685/23189-0, Fax: DW 4, E-Mail: [email protected], Homepage: http://www.bachler.at

 

current, move the red lead to the 10A jack. Set the rotary switch at the desired 

 range position. Connect test leads in series 

with the load under measurement. You can get reading from LCD. The polarity of the red lead connection will be indicated along 

with the current value. 

 

NOTE: 

1. When the value scale to be measured 15 unknown beforehand, set the range selector at the highest position. 

2. When only the figure '1' or '-1' is displayed, it indicates over-ange situation and the higher range has to be selected. 

3. “

“ means the socket mA’s maximum current is 200mA and 1O0A's maximum current is 10A, over current will destroy the 

fuse. Since 10A is not fused, the measuring time should be less than 1 second to prevent precision from affecting by circuit 

heating. 

 

7-5 Measuring Resistance 
 

Connect the black test lead to COM jack and the red to V

mA jack. Set the rotary switch at the desired 

 range position. 

Connect test leads across the resistance under measurement. You can get reading from LCD. 

 
NOTE: 

1. When only the figure '1' or '-1' is displayed, it indicates over-range situation and the higher range has tobe selected. 

2. 

For measuring resistance above 1M

 the mete may take a few seconds to get stable reading. 

3. When the input is not connected, i.e. at open circuit

the figure '1' will be displayed for the over-ange condition. 

4. When checking in-circuit resistance, be sure the circuit under test has all power removed and that all capacitors have been 

discharged fully. 
5. The value scale to be measured is unknown beforehand, Set the range selector at the highest position. 
 

7-6 Measuring Temperature 

 

Set the rotary switch at the °C range position. The LCD will 50W the current temperature of the environment. When measuring 

temperature with thermocouple, temperature probe for this meter can be used. Insert 'K' type thermocouple probe (red one into 

V

mA jack and black one into COM jack). You can get a reading from LCD. In order to guarantee the accuracy of the 

measurement, need to close light switch while measuring temperature. 

 

7-7 Transistor Testing 

Set the rotary switch at 'hFE' position. Determine whether the transistor under testing is NPN or PNP and Iocate the emitter, 

base and collector leads. Insert tne leads into proper holes of hFE socket on the front panel. Read the approximate hFE value at 

the testing condition of base current lb10uA and Vce 3V. 

 

7-8 Diode Testing 
 

Connect the black test lead to COM jack and the red to V

mA jack (the polarity of red lead is +). Set the rotary switch at the   

F range position. Connect the red lead to the anode and the black lead to the cathode of the diode under testing. You can get a 

reading from LCD. 

 
NOTE: 

1. The meter will show approximate forward voltage drop of the diode. 

2. If the Iead connections is reversed, only '1'

 

will be displayed. 

 

7-9 Continuity Testing 
 

Connect the black test lead to COM jack and the red to V

mA jack. Set the rotary switch at the 

 range position. test Ieads 

across two points of the circuit under testing. If continuity exists (i.e. resistance less than about 50

), built-in buzzer will sound. 

 

NOTE: 
If the input open circuit, the figure '1' will be displayed. 
 

8. Maintenance 
 

Before attempting to remove the battery door or

 

open the case, be

 

sure that test leads have been disconnected from 

measurement circuit top avoid electric shock hazard. To avoid electrical shock

remove test leads from rneasurement circuits 

before replacing the fuse. For protection against fire, replace fuses only with specified ratings: F-200mA/250V fuse. You must 

replace the test teads if the lead is exposed, and should adopt the leads with the same specifications as origin. Use only moist 

fabric or small amount of detergent but not chemicaI solutio for cleaning. Do not use the meter before the back cover is properly 

closed and screw secured. Upon any abnormality, stop operation immediately and send the meter for maintenance. 

 

9. Accessories 
 

Test Leads: electric rating 1000V 10A 

Battery: 9V, 6F22 or NEDA 1604 

Fuse: F-200mA/250V 

'K' type Thermocouple 

Operator’s Manual 

Holster 

Summary of Contents for Solarcheck DT-36T









Reviews: