background image

MGS-401 User Manual

 

 

 

8.

 

Parts Numbers and Service 

8.1

 

Part Numbers 

 

      Part # 

Description 

6702-8030 

MGS-401 Entrance Monitor 

6600-8950 

Sunshield for outdoor locations 

1100-8950 

Security Screws ((6) pcs. and driver bit) 

6900-0010 

>100dB External sounder (mounted in MGS-401 Cable Gland) 

www.mybacharach.com  MGS Family of Gas Detectors 

8.2

 

Service Center Locations 

Prior to shipping equipment to MSA Bacharach, visit www.mybacharach.com for a Returned 

Merchandise Authorization Number 

(RMA #)

. All returned goods must be accompanied by an RMA #. 

Pack the equipment securely 

(in its original packing, if possible)

, as MSA Bacharach cannot be held 

responsible for any damage incurred during shipping to our facility. 

 

Location 

Contact Information 

Shipping Address 

United States 

Phone: +1 724 334 5000 

Toll Free: +1 800 736 4666 

Fax: +1 724 334 5001 

Email[email protected] 

MSA Bacharach, Inc. 

621 Hunt Valley Circle 

New Kensington, PA 15068, USA 

ATTN: Service Department 

Europe 

Phone: +353 1 284 6388 

Fax: +353 1 284 6389 

Email[email protected] 

MSA Bacharach, Inc. 

Unit D12 & D13 Santry Business Park, Swords Road 

Santry, Dublin, Ireland 

ATTN: Service Department 

Canada 

Phone: +1 905 882 8985 

Fax: +1 905 882 8963 

Email[email protected] 

MSA Bacharach, Inc. 

10 West Pearce Street, Unit 4 

Richmond Hill, Ontario. L4B 1B6, Canada 

ATTN: Service Department 

 
 

 

 
 
 

 

 

 

Summary of Contents for MGS-401




















Reviews: