BBS05-IM-120423
When using electrical appliances, basic safety precautions should always be followed including the following:
READ ALL INSTRUCTIONS
Always use the steam sterilizer on a flat surface.
DO NOT expose the sterilizer to source of heat such as a radiator or sun shining through a window.
To protect against risk of electrical shock, NEVER put sterilizer power base in water or other liquids. Clean the sterilizer with damp cloth, then let
it dry completely.
Close supervision is necessary when any appliance is used near children or incapacitated persons.
NEVER use detergent or corrosive substances to clean the steam sterilizer.
NEVER use the appliance without water.
The sterilizer will stop automatically with a warning signal in case of lack of water. In such case, please fill the unit with recommended amount of
water and run a complete sterilizing cycle again to ensure proper sterilizing is achieved.
Please always fill the recommend amount of water or it may alter the sterilization quality.
Unplug the sterilizer from outlet when not in use, before cleaning or changing accessories.
DO NOT operate the sterilizer with a damaged cord or plug or after appliance malfunctions, or is dropped or damaged in any manner.. Return the
appliance to the nearest Authorized Service Center for examination, repair or electrical or mechanical adjustment.
Any servicing should be performed by an authorized service representative.
NEVER unplug the product during the sterilizing cycle or otherwise it will reset the sterilizing cycle. In case of mistakenly unplugging of the
product during the sterilizing cycle, you need to restart the sterilizing cycle completely again to ensure a correct sterilizing quality can be
achieved.
Use of any attachments is not recommended as it may cause fire, electric shock or injury.
DO NOT use outdoors.
DO NOT let the cord hang over the edge of the table or counter.
DO NOT let cord contact any hot surface.
DO NOT immerse in water.
This appliance is not intended for use by persons ( including children) with reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
Ensure nothing is rested on the heating element surface (the stainless steel surface on the base) before starting the sterilizing process.
When in use, the sterilizer contains boiling water. Hot steam will escapes from the vents of the lid.
Take care when opening the lid as steam can burn.
NEVER open the unit when in use.
NEVER place any item on top of the sterilizer.
Stop the sterilizer during the sterilization cycle only when absolutely needed by pressing the start/stop button or unplug from the mains.
THIS PRODUCT IS INTENDED FOR HOUSEHOLD USE ONLY
DO NOT plug the appliance in before checking what the voltage indicated on the rating plate is the same as the electrical
supply voltage.
UK ONLY
The wires in the cord are colored as follows:
Blue = Neutral
Brown = Live
Green / Yellow = Earth
(Refer to the Display Panel Guide for the operation status)
Unpack all parts of the sterilizer from the packing and remove all plastic bags.
Prior to first use, wash lid, top rack, top tray, sterilizer body, central stem, bottom rack, measuring cup and tongs,
After washing, measure 200ml of tap water with the milk bottle or measuring cup and pour it to the sterilizer base unit.
Now fix the central stem to the bottom tray and then place them on the base unit, then place the sterilizer body, top tray, top rack and lid in
sequence as per the diagram. The tongs should place on the top rack before closing it with the lid.
Connect the plug into the mains supply.. The start/stop “ ” icon on the panel will light up in red color.
Press and hold the start/stop button for 1 second to allow the sterilizer to progress through a cycle until the “ ” icon turn to green color.
Remove the lid, racks, and trays from the sterilizer base and pour away any remain water in the base. Wipe all parts with clean dry clothes.
Before sterilizing, disassemble all parts of the bottle and wash them with mild soapy water and rinse.
Measurer 200ml of water with the measuring cup or a milk bottle (a) and then pour the water in the sterilizer base (b).
Place the bottom rack with the central stem fixed (c) onto the sterilizer base (d).
Place the screw rings to the central stem (e);
Load the milk bottle body with neck downwards and slot it to the location ribs provided on the bottom rack (f).
Cover the bottom rack with the sterilizer body (g);
Place the top tray and the top rack on the sterilizer body (h & i).
Place the teats, caps, and tongs onto the top rack (j).
Cover the top rack with the lid (k).
Connect the plug into the mains supply .
Push the start/stop button (l) to start the sterilizing cycle with detail progress as per the display panel guide.
This product is specially designed with a cooling stage to ensure sterilizer parts, and sterilizing item are cool down to a temperature that is safe to
touch. The change of the “ ” icon from red to green color indicates the cooling process is completed.
Wash your hands before removing the sterilized items.
Now you can open the sterilizer lid and place it upside down on the bench.
Remove the top tray (with the top rack and all accessories) from the sterilizer and place it on the upside down lid.
Remove the sterilizer body to access the milk bottles and screw rings.
Now you can assemble the milk bottle with the help of using the tongs. Tongs is for remove small items and also for removing the sterilized teats
through the screw ring. If needed, shake excess water from items before assembling.
Items will remain sterilized for 3 hours provided the sterilizer lid keep not open after the sterilizing cycle. The stable green “ ” indicate these
“keep sterilized stage” provided that you did not push the start/start button to reset sterilizer.
After 3 hours, the sterilizer will beep for 10 times and the “ ” icon will change to flash in red. The “ ” change to flashing in red color indicates the
sterilized item is no good for use anymore and a new complete sterilizing cycle is needed before using any item in the sterilizer.
Milk bottle sterilizing configuration
Breast Pump sterilizing configuration
This sterilizer is specially designed for the easy sterilizing of breast pump parts by just using the upper parts of the sterilizer with the base.
Add 200ml of water to the sterilizer base.
Place the top rack on the sterilizer base directly.
Slot the breast pump to the appropriate slot provided on the top rack and arrange other breast pump parts onto the top rack.
Other processes are identical to the standard bottle sterilizing process.
Switch off, unplug and disassemble before cleaning.
Do not let the power base, cord or plug get wet.
Wipe power base with damp cloth, then dry, avoiding the use of abrasive detergents.
Do not use bleach or chemical sterilizing solution/tablets in your steam sterilizer
STERILIZER CONFIGURATION
STERILIZE 6 SETS OF MILK BOTTLES
BEFORE THE FIRST USE OF YOUR
STERILIZER
STERILIZING BREAST PUMPS
USING THE STERILIZED ITEMS
SAFETY INFORMATION
BEFORE PLUGGING THE STERILIZER
CLEANING
