Baby Lock Sofia BL137A2 Instruction And Reference Manual Download Page 12 | Manualshive

Page: 12 / 188

background image

10

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

Needle and presser foot
section

a

Buttonhole lever (page 88)

Lower the buttonhole lever when sewing buttonholes
and bar tacks.

b

Thread guide disk (page 32)

Pass the thread through the thread guide disk when
using the needle threader to thread the needle.

c

Needle bar thread guide (page 32)

Pass the upper thread through the needle bar thread
guide.

d

Needle plate (page 67)

The needle plate is marked with guides for sewing
straight seams.

e

Needle plate cover (page 170)

Remove the needle plate cover to clean the bobbin case
and race.

f

Bobbin cover/bobbin case (page 26)

Remove the bobbin cover, and then insert the bobbin
into the bobbin case.

g

Feed dogs (page 90)

The feed dogs feed the fabric in the sewing direction.

h

Presser foot (page 41, 50)

The presser foot applies pressure consistently on the
fabric as the sewing takes place. Attach the appropriate
presser foot for the stitch selected.

i

Presser foot holder (page 43)

The presser foot is installed onto the presser foot holder.

Right-side/rear view

a

Handle

Carry the sewing machine by its handle when
transporting the machine.

b

Handwheel (page 50)

Turn the handwheel toward you (counterclockwise) to
raise and lower the needle to sew one stitch.

c

Embroidery card slot (page 150)

Insert the embroidery card.

d

USB port (for a USB flash drive (USB flash memory))

In order to import patterns from a USB flash drive (USB
flash memory), plug the USB media directly into the
USB port.

e

Air vent

The air vent allows the air surrounding the motor to be
exchanged. Do not cover the air vent while the sewing
machine is being used.

f

Main power switch (page 15)

Use the main power switch to turn the sewing machine
on and off.

g

Foot controller jack (page 52)

Insert the plug on the end of the foot controller cable
into the foot controller jack.

h

Power supply jack (page 15)

Insert the plug on the power supply cord into the power
supply jack.

i

Drop feed lever (page 90)

Use the drop feed lever to lower the feed dogs.

Memo

z

Refer to pages 9 through 12 while you are
learning to use your machine.

«
...
10
11
12
13
14
...
»

Summary of Contents for Sofia BL137A2





























































































































































































Reviews:

No comments

Related manuals for Sofia BL137A2

Brand: Banner Pages: 11

Brand: Janome Pages: 31

In-Sight 7600 Series

Brand: Cognex Pages: 90

Brand: National Instruments Pages: 18

In-Sight 8000 Series

Brand: Cognex Pages: 116

HAKOMATIC B 90 CL

Brand: HAKO Pages: 42

Brand: Olivetti Pages: 16

Brand: Janome Pages: 52

Brand: GBC Pages: 18

Brand: IPC Eagle Pages: 40

Brand: Panasonic Pages: 35

Brand: Panasonic Pages: 50

Brand: Panasonic Pages: 76

Brand: Panasonic Pages: 72

Brand: Panasonic Pages: 76

Brand: Panasonic Pages: 72

Brand: Panasonic Pages: 92

Brand: Panasonic Pages: 84

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands