Baby Lock Sofia BL137A2 Instruction And Reference Manual Download Page 184 | Manualshive

Page: 184 / 188

background image

182

APPENDIX

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

Upgrading Your Machine’s Software Using USB Media

You can use USB media and a computer to download software upgrades for your sewing machine.
When an upgrade program is available on our website at “ www.babylock.com

”, please download the

file(s) following the instructions on the website and steps listed below.
You can use USB to download software upgrades/updates (

. up5) for your sewing machine.

Note

z

When using USB media to upgrade the software, please reformat the USB media so that no data other
than the upgrade file will be saved on the USB media before starting to upgrade.

z

Upgrade files can be retrieved from a USB flash drive (USB flash memory) of any size.

Memo

z

When the machine's software is upgraded, saved combinations of character and decorative stitches are
erased. However, saved embroidery patterns are not erased.

a

Press and hold the

(Settings key) while

turning on the machine.

X

The following screen appears.

b

Insert the USB media into the USB port on the
machine. The media device should only
contain the upgrade file.

a

USB port for media

b

USB media

Note

z

When using USB media equipped with an
access indicator, the access indicator will
begin flashing after the media is inserted into
your computer or machine, and may take
about 5 to 6 seconds before the media is
recognized. (The length of time differs
depending on the USB media.)

c

Press .

X

The following screen appears.

Note

z

If an error occurred, a text error message will
appear. At this time, turn the machine off,
and then start the procedure again from step

a

.

d

When the following screen appears, upgrading
is completed.

e

Remove the USB media, and turn the machine
off and on again.

«
...
182
183
184
185
186
...
»

Summary of Contents for Sofia BL137A2





























































































































































































Reviews:

No comments

Related manuals for Sofia BL137A2

Brand: Panasonic Pages: 256

KXFG2451 - B/W Thermal Transfer

Brand: Panasonic Pages: 20

UF 8200 - Panafax - Multifunction

Brand: Panasonic Pages: 6

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 150

Brand: Panasonic Pages: 112

Brand: Panasonic Pages: 12

KX-FL521 - B/W Laser - Fax

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 50

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 84

Brand: Panasonic Pages: 104

Brand: Panasonic Pages: 24

In-Sight 7600 Series

Brand: Cognex Pages: 90

Brand: MAGIC FX Pages: 20

Brand: National Instruments Pages: 18

884-xxx-M series

Brand: Dürkopp Adler Pages: 40

Pro Climber C525i

Brand: Tunturi Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands