background image

www.babylock.com

MACHINE SETTINGS

Stitch type: 

4-Thread Overlock

Stitch width: 

M-7.5

Needle: 

01 and 02

Stitch length: 

4

Upper knife: 

Engaged “UNLOCKED”

Differential feed: 

2

Stitch selector: 

A

Sewing speed: 

Slow to moderate

 

GATHERING FABRIC:
Place one layer of fabric under the presser foot and sew. 
Generously feed fabric. The fabric will gather as you sew.

SHIRRING:
1.  Place fabric to be gathered right side up under the presser 

foot and under the separator. 

2.  Position the fabric up to the needles. Turn handwheel 

forward  3-4 times to catch the fabric with the needles.

3.  Place the fabric to attach the gather to right side down on 

top of the separator. (See illustration.) This keeps the fabric 
away from the feed dogs.

4.  Place the fabric up to the needles. Turn the handwheel 3-4 

turns to catch the fabric with the needles.

5.  Gently guide the upper fabric into the separator while 

generously guiding the lower fabric that is being gathered 
under the separator. The ruffle will be sewn to the flat 
fabric while sewing.

Easily make and attach ruffles as well as finish your edge in 
one simple step. Add perfectly spaced ruffles to garments, 
pillows, and other home décor items. This ruffling foot works 
on all fabric types.

Ruffling Foot

(BLE8-RF) 

 Instructions

Note: Gathering works the best with fine fabrics. The 
heavier the fabric the less the gathering.

Summary of Contents for Ovation





















Reviews: