background image

       

31

Stylus and Adaptor Plate

A stylus is used to follow the grooves of pattern boards. It is attached 

by an adaptor plate to the machine’s rear base plate on the right side 

of the machine (when you are facing the front of the machine). The 

machine’s rear base plate has two holes pre-drilled on the right side 

to accommodate the stylus holder (

Photo 4

).

Installing the Adaptor Plate

To attach the adaptor plate, lay the machine on its left side and place 

the adaptor plate over the two square holes, with the rectangular  

hole over the wheel. Place the two carriage bolts down through the 

adaptor (the square holes are for locating and holding the carriage 

bolt head during tightening). Attach with the two lock nuts on the 

bottom of the machine’s base plate (

Photo 5

) and tighten until the 

bracket is firm and does not move. Lift the machine upright and 

place back on the carriage for the next step.

Photo 5

Photo 4

Photo 6

Photo 7

Installing the Stylus Holder

The stylus holder has two threaded holes. Place  

the stylus holder under the adaptor plate and align 

the two holes with the long slot in the adaptor 

plate. Place the two wingbolts first through the  

slot and then thread into the stylus holder as 

shown (

Photo 6

). Note that the stylus holder is 

mounted under the adaptor plate and that the  

stylus opening and thumb screw go towards the 

front of the machine as shown.

Installing the Stylus

The stylus is mounted into the stylus holder and 

secured with the thumb screw which faces the front 

of the machine (

Photo 4

). The height of the stylus 

is set once the pattern board is set onto the table. 

With the thumb screw loosened slightly, lower the 

stylus so that the stylus tip will go into and stay 

in the groove as the machine is moved (

Photo 7

). 

Tighten the thumb screw. 

If the stylus is set too high, it can inadvertently 

come out of the groove while quilting. If set too 

low, it will cause unwanted resistance during  

quilting and will wear the stylus tip prematurely. 

Please note that the stylus is a consumable part. 

The tip will eventually wear down and the stylus 

will need to be replaced.

Lock Nuts

Thumb

Screw

Wingbolts

Stylus Holder

Stylus

Adaptor

Plate

Carriage Bolts

Summary of Contents for Jewel BL J18



































Reviews: