BAB TECHNOLOGIE DUODMX GATEWAY Documentation Download Page 49

Page: 49 / 52

DUO DMX

Gateway

Device Type „Extension“ (EIBPORT Extension)

DUO DMX

Gateway

b.a.b-technologie gmbh 49

System ID

In addition, for the facilities coupling a so-called "

System ID

" is used. That's a number from 0-255 and is

used -in the case of the facility coupling - to differ coupled KNX facilities from each other in virtual

plants. For the DUO

DMX

GATEWAY the EIB

PORT

has to have the system ID "0". The system ID is set

under "

System

" - "

Advanced EIB (yabus) Settings

" - "

Configuration

Network settings

EIB

PORT

and DUO

DMX

GATEWAY must not be in the same network area for communication. The

control can (with appropriate firewall - configuration) also take place over the internet.

7.2

EIBPORT JOB „LINKING FACILITIES“

If the messages should be transferred over the BMX protocol to the DUO

DMX

GATEWAY the "

linking

facilities

" job is used. This job is also described in the documentation of EIB

PORT

. Important

communication parameters are

Figure 58: EIBPORT Job – Linking Facilities

Host name / IP address

Enter the IP address of the DUO

DMX

GATEWAY. If the communication is done via the internet here a

DynDNS address entered.

connection Type

It is used for the direct connection via LAN ("direct (LAN)")

Summary of Contents for DUODMX GATEWAY





















































Search results

Summary of Contents for DUODMX GATEWAY

Reviews:

Related manuals for DUODMX GATEWAY

Brands by name

Popular brands

BAB TECHNOLOGIE DUODMX GATEWAY, Documentation

Search results

Summary of Contents for DUODMX GATEWAY

Reviews:

Related manuals for DUODMX GATEWAY

Brands by name

Popular brands