9. Settings by remote control IR-PD-2C
10. Key functions in closed state
Unlocking device - Activation of the programming mode
Locking device - Exit programming mode
Done for about 3min. no further action, will be deactivate
the programming mode automatically.
Change between fully automatic
and semi automatic mode (HA)
Luminance set point for channel 1
20 - 1000 Lux
Automatic reading in the current light value as new
luminance set point
Change between motion detector and
photo electric switch
Gradually increase the current light level by
20 resp 50 Lux
Light ON/OFF
HA
ON/OFF
Light ON/OFF during the detection of motion plus
follow-up time;
Activation of the 12 h-ON/OFF-function by holding
down the push button
Switches channel off and is immediately active again,
exits all timers, interruption of light measurement
Permanent protection against sabotage
This function blocks the
LUXOMAT
®
PD2-M-2C-11-48V
permanently. This operating mode can only be
activated during the period of 5 seconds (white LED
flash) after pressing the “lock“ button. The procedure
for leaving this mode is as follows:
1. Switch off the current
2. Apply current for 31 - 59 seconds
3.
Switch of the current again
4. Apply current, wait for selftest cycle
5.
Open detector
Changes to “open“ state
Resetting when
open:
Deletes
all values set
with the remote
control, light OFF.
Potentiometer
and DIP switches
are enabled for
setting.
or
1000
20
to
+
Follow-up time ch1 (light)
5 - 30 min. or impulse
Follow-up time ch2 (HVAC)
5 - 30 min. resp. 120 min. or impulse
��
���
to
LED ON/OFF (by holding down the push button)
Activation/Deactivation of the test function
After 3 minutes the test mode will be automatically
closed.
Confirmation
Detection sensitivity reduced or normal
Daytime operation, detector only activated by motion
or
PI R
CdS
Permanent protection against sabotage
White LED flashes
for c
hoice CdS
max
50
Lux
1500
Lux
ON
OFF
Option: Remote control IR-PD-2C
Wall bracket for remote control
IR-PD-2C
An adhesive film for the surface of the IR-PD-2C-S is inclu-
ded with the device. If required, this can be used for any
B.E.G.
remote control with 27 keys.
In order to benefit from the whole range of functions of
the PD2-M-2C-11-48V, please order separately the remote
control IR-PD-2C.
8. Putting into operation of the remote
control IR-PD-2C (optional)
Check Battery:
Open battery compartment
by pressing the plastic springs
together and removing the
battery-holder.
Caution:
Settings with remote control supersede
the settings by potentiometers.
1
2
120 6050
40
30
15
10
A
16 10
5
2
1
30
15
TEST
2000
1200
600
200
40
5
120 6050
40
30
15
10
A
16 10
5
2
1
30
15
TEST
2000
1200
600
200
40
5
t < 5 s
LUXOMAT
®
PD3
B.E.G.
B.E.G.
LUXOMAT
®
B.E.G.
LUXOMAT
®
500
200
400
100
20
IR-PD-2C-S
ON/OFF
HA
min
30
min
60
min
120
B.E.G.
LUXOMAT
®
R2
R1
R1
Film IR-PD-2C-S
IR-PD-2C - 92475
or
7. Reset and default settings
1. Default settings
If the potentiometers are in the
“Test“ and “Sun“ position and the
detector is unprogrammed, the
factory program is activated:
500 Lux and 10 min.
2. Reset
If both potentiometers are returned to the ”Test“ and “Sun“
setting from any other position, a reset is executed. All values
programmed with the remote control are deleted.
��
���
��
���
5
min
120
min
5
min
max
50
Lux
1500
Lux
ON
OFF
t < 5 sec.
optional
optional
optional
optional
optional
optional
