manualshive.com logo in svg

B+B SmartWorx SPECTRE v3 LTE, User Manual, Page: 50 / 50

Share
Download
B+B SmartWorx SPECTRE v3 LTE User Manual Download Page 50

10. CUSTOMERS SUPPORT

10. Customers Support

10.1

Global Customer Support

You can find up to date information about this product on our website:

www.conel.com

Upkeep-advices:

•

The SIM-card must be handled carefully as with a credit card. Don’t bend, don’t scratch
on this and do not expose to static electricity.

•

During cleaning of the router do not use aggressive chemicals, solvents and abrasive
cleaners!

Conel Company hereby declares that the router narrated in this user’s guide fits all basic
demands of directive 1999/5/EC (R&TTE).

Router fits values of coefficient SAR defined by association ICNIRP and values of "About
protection of health before non-ionized radiation".

Declaration of Conformity was issued and it is possible to find it on the Conel
website (

http://www.conel.com/download

)

1

or at producer.

10.2

Customer Support for NAM

Up to date product information is on the website:

www.bb-smartworx.com

For Technical Support:

Call 815-433-5100

1

Please, use the following login information: Username – ConelFreeDownload, Password – coneldownload.

42

Summary of Contents for SPECTRE v3 LTE



















































Reviews:

No comments