manualshive.com logo in svg

B+B SmartWorx SPECTRE v3 LTE, User Manual, Page: 23 / 50

Share
Download
B+B SmartWorx SPECTRE v3 LTE User Manual Download Page 23

5. ROUTER DESIGN

5.8.1

Status indication

About router status inform nine LED indicators on the front panel. Each ETH port has two

additional LEDs that provide information about port status.

Caption

Color

State

Description

PWR

Green

Blinking
On
Fast blinking

Router is ready
Starting of the router
Updating firmware

USR

Yellow

—

Function of this LED diode can be selected by user

POE

Yellow
Green

—

—

SIM

Yellow
Green

On (Yellow color)
On (Green color)

The first SIM card is active
The second SIM card is active

WAN

Yellow

1x flash per sec.
2x flash per sec.

3x flash per sec.

Signal strength is from –50 dBm to –69 dBm
Signal strength is from –70 dBm to –89 dBm or differ-
ence between neighbours cells is exactly 3 dBm
Signal strength is from –90 dBm to –113 dBm or differ-
ence between neighbours cells is smaller than 3 dBm

DAT

Red

Blinking

Communication in progress on radio channel

IN0

Green

On

Binary input no. 0 is active

IN1

Green

On

Binary input no. 1 is active

OUT

Yellow

On

Binary output is active

ETH0
ETH1

Green

On
Off

Selected 100 Mbit/s
Selected 10 Mbit/s

ETH0
ETH1

Yellow

On
Blinking
Off

The network cable is connected
Data transmission
The network cable is not connected

Table 9: Status indication

State indication of WAN LED is updated every 10 seconds.

15

Summary of Contents for SPECTRE v3 LTE



















































Reviews:

No comments