manualshive.com logo in svg

B+B SmartWorx SPECTRE v3 LTE, User Manual, Page: 2 / 50

Share
Download
B+B SmartWorx SPECTRE v3 LTE User Manual Download Page 2

HEADQUARTERS

International Headquarters

B&B Electronics Mfg. Co. Inc.

707 Dayton Road
Ottawa, IL 61350 USA

Phone

(815) 433-5100 –

General Fax

(815) 433-5105

Websites

www.bb-smartworx.com
www.bb-smartsensing.com
[email protected]

European Headquarters

B&B Electronics

Westlink Commercial Park
Oranmore, Co. Galway, Ireland

Phone

+353 91-792444 –

Fax

+353 91-792445

Websites

www.bb-europe.com
[email protected]

c

2015 B&B Electronics Mfg. Co. Inc. No part of this publication may be reproduced or transmitted in any

form or by any means, electronic or mechanical, including photography, recording, or any information storage and
retrieval system without written consent. Information in this manual is subject to change without notice, and does
not represent a commitment on the part of B&B Electronics Mfg. Co. Inc.

B&B Electronics Mfg. Co. Inc. shall not be liable for incidental or consequential damages resulting from the

furnishing, performance, or use of this manual.

All brand names used in this manual are the registered trademarks of their respective owners. The use of

trademarks or other designations in this publication is for reference purposes only and does not constitute an
endorsement by the trademark holder.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the

following 2 conditions: (1) this device may not cause interference, and (2) this device must accept any interference,

including interference that may cause undesired operation of the device.

i

Summary of Contents for SPECTRE v3 LTE



















































Reviews:

No comments