Azbil MagneW 3000 User Manual Download Page 12

Overview

Azbil Corporation

8

Model MGR13C/MGR11U - MagneW3000 Electromagnetic FLowmeter Hyper-Fill 

3 :  Configuration of the converter

Refer to the following configuration table printed to the main unit for the converter 
configuration.

3-1 : Range

Select an appropriate range. It is recommended to set a range so that the flow rate is 
approximately 70%. Do not set a range of which the flow rate is less than 25%. 

Select the range by receptacles in S2 shown in Figure 5.

3-2 : Pulse scale

0.1 mL/P or 0.05 mL/P is selectable as a pulse scale.

Pulse scale of 0.05 mL/P is not applicable in case of range of 800 mL/s. 

~Note

*  Pulse width of 200 

μ

S is not applicable in case that pulse span fre-

quency fs is 8000 Hz.

Figure 5  

Range

100 mL/s

200 mL/s

400 mL/s

800 mL/s

Range

100 mL/s

200 mL/s

400 mL/s

800 mL/s

Pulse span 
frequency fs

0.05 mL/P

2000 Hz

4000 Hz

8000 Hz *

   N/A

 0.1 mL/P

1000 Hz

2000 Hz

4000 Hz

8000 Hz *

S2

S3

S4

100mL/s

100mL/s

200mL/s

200mL/s

400mL/s

400mL/s

800mL/s

800mL/s

RANGE

PULSE WEIGHT

RANGE

PULSE WIDTH

0.1mL/P

0.05mL/P

0.05mL/P

0.05mL/P

0.1mL/P

0.1mL/P

0.1mL/P

30

μ

s

200

μ

s

Summary of Contents for MagneW 3000





















Reviews: