background image

- Avoid nearby flames or heat sources, do not place this device near flammable liquids, gas or flammable 
items.
- Always disconnect the device when it is not in use for a longer period or time, when servicing is needed or 
when the device needs cleaning.
- Only handle the power cord by its connectors. Never pull the cable to remove a connector from its socket, 
as this could lead to damage and electrical shocks.
- Always operate this device with a stable AC current.
- Always operate this device with the AC ground wire connected to the electrical system's ground.
- Never use other types of cables than specified in the manual, do not use defective or bad functioning 
cables. Contact your dealer when the included or required cables do not work properly with this device.
- When the device has been exposed to large temperature differences (for example, transport from outdoor 
to indoor), do not connect the device immediately. Do not activate the unit until it has reached room 
temperature, as moist might build up inside the unit, which may cause shortcuts and/or electrical shocks.

Guidelines and types of use:

- This device is intended to be used by professionals on stage, in theaters, clubs and other equal venues. 
- This device is not suitable for children and always needs to be operated by an adult.
- Only use the device when the environment is suitable and will not cause any damage. Do not use the 
product in moist or dusty environments, or where long-term damage may occur such as: 

- indoor swimming pools where chlorine is used.
- Beaches, where sand and salt are present.
- Outdoor, without roof protection
- Indoor areas where intense heat sources are present or where the temperature exceeds levels 

which are comfortable for humans.
- Only use the included power adapter and only connect the device to a suitable power outlet with the correct
output voltage. Connecting the device to a power outlet with the wrong type of voltage or using the product 
with a wrong type of power supply may cause permanent damage to the device.
- Avoid shocks and collision during use and transport. Do not transport the device while in use. Avoid brute 
force during the installation and operation of this device.
- Familiarize yourself with the functions of the device before use. Do not allow operation of the device by 
unskilled or unqualified people.
- Use of the device in other ways than described in this user manual may cause damage and injury. Ayra 
does not take responsibility for any damage or injury caused by improper use.

Storage and transport:

- This device is intended for mobile use. When transported, use the original packaging of the product, or a 
fitting flightcase, preferably filled with foam.
- This device is not intended for permanent use. Operation breaks will ensure that the lifespan of the device 
remains unchanged.
- If the device is not used for a longer period of time, disconnect it from its power source and store it in its 
original packaging, or in a fitting flightcase.
- Store the device indoor, dry and do not expose the device to extreme temperature differences.

Housing:

- Inspect the housing of the device frequently. Severe dents, cracks and missing screws should be avoided 
at all costs. Do not use the device when the housing is not in optimal condition. Contact your dealer or a 
skilled technician when in doubt about the state of the device
- Check the fixture and screws for corrosion. Corrosion should not be present on the fixture. Contact your 
dealer or a skilled technician when corrosion is found on the fixture
- Every power or signal chassis/connector should be mounted tightly. Do not use the device when connectors
are loose.
- Do not use the power cord when the cores are visible. Contact your dealer for a replacement if needed.
- Avoid the buildup of dust and dirt. Clean the exterior of the fixture every month with a dry or damp cloth. 
When using the device intensively, the cleaning frequency needs to be increased.

Fuses:

- The main fuse of this device is to be found on the rear of the device. In most cases, directly next to the 
power inlet. 
- Only replace a fuse for a new one with the same type and rating! Do not use a fuse with a higher or lower 

Any information and illustrations shown in this user manual are subject to change without further notice.

User manual version: 2.0

Creation date + author initials: 05-12-2013 RV Revision date + author initials: 18-02-2014 RV

Summary of Contents for ITA3D 80














Reviews: