background image

AXON CORPORATION – EZ-SEAL  

August 21, 2001 

 

 

Page 3 

 

SPECIFICATIONS

 

 

MODEL 

EZ-24 

BR/SR 

EZ-36 

BR/SR 

EZ-48 

BR/SR 

EZ-72 

BR/SR 

EZ-30-IR 

Technology 

Convective – (Forced Hot Air – Re-circulated) 

Radiant 

(Infra-Red) 

Standard Tunnel Opening  
(Note 1) 

7.5” wide x 6.75” high 

3” wide 

6” high 

220-240 VAC 
50/60 Hz. 
Single Phase 

33 Amps  66 Amps ( 2 x 33 Amps)  2

4

 Amps 

Electrical  
Specifications  480 VAC  

50/60 Hz.  
3 Phase 

15 Amps 

30 Amps ( 2 x 15 Amps) 

N/A 

Length (Note 2) 

24” 

36” 

48” 

72” 

30” 

Width (Note 3) 

18” 

10” 

Space 
Requirements 

Height (Note 4) 

24” 

10” 

Weight 

(lbs) 

90 120 180 240 50 

Notes:  1 – Custom Tunnel opening sizes are available contact Axon Corporation.  

2 – Length of the EZ-48 and EZ-72 increase by 2” when conveyor mounted with Auto Tunnel  
Lift option. 
3 – Width of the tunnel can be increased to accommodate larger products.  
4 – Height of the tunnel can be increased to accommodate longer/taller sleeves.   

 

 
 

 
1341 Express Drive, Raleigh, NC, USA 27603                  

Phone (919) 772-8383 

http://www.axoncorp.com

  

Fax 

(919) 

772-5575 

Summary of Contents for EZ-24 BR













Reviews: