background image

Wood Dust Collector Safety Instructions 

Read this entire Manual before using this machine. 

1. Maintenance. 

Make sure the Dust collector is 

turned off and disconnect from the main power 
supply and make sure all moving parts have come to 
a complete stop before any inspection, adjustment 
or maintenance is carried out. 

8. Hearing protection and hazards. 

Always wear 

hearing protection as noise generated from dust 
collector can cause permanent hearing loss over 
time. 

2. Dust collector Condition. 

Dust collector must be 

maintained for a proper working condition. Never 
operate a Dust collector that has damaged or 

9. Dust Collector use. 

This Dust Collector is designed 

to be used with wood & Metal only. Do not pick 
up material that can not safety pass through the 
impeller. 

worn parts. Scheduled routine maintenance should 
performed on a scheduled basis. 

10. Fire Hazard. 

Ensure machines and hoses are 

3. Inlet Hazard. 

Do not place hands or tools near the 

open inlets during operation for any reason. The 
impeller could cause serious damage to body parts if 
touched while spinning. 

4. Avoiding Entanglement. 

Guards and dust bags 

must be used at all times. Remove loose clothing, 
belts, or jewelry items. Tie up long hair and use the 

thoroughly cleaned inside and out of all wood 
dust and chips before using this machine for steel 
dust. Ensure the dust extraction hose used is heat 
resistant and flame retardant and a minimum length 
of 2 meters between machine and dust collector. 

11. Bags & guards. 

All safety bags and guards must 

be used at all times. Bags must be replaced when 
damaged. 

correct hair nets to avoid any entanglement with the 
Dust collector. 

12. Emptying bags hazard. 

Always wear a respirator 

5. Understand the machines controls. 

Make sure you 

and safety glasses when emptying dust into 
approved containers and dispose of properly. 

understand the use and operation of all controls. 

6. Power outage. 

In the event of a power failure 

during use of the Dust collector, turn off all switches 
to avoid possible sudden start up once power is 
restored. 

13. Wood dust may cause allergic reactions. 

Make 

sure you know what type of dust you are exposed 
to as it may cause you an allergic reaction. Always 
wear an approved respirator. 

7. Work area hazards. 

Keep the area around the Dust 

collector clean from oil, tools, chips. Pay attention to 
other persons in the area and know what is going on 
around the area to ensure unintended accidents. 

14. Call for help. 

If at any time you experience 

difficulties, stop the machine and call you nearest 
branch service department for help

Summary of Contents for T-2000CK





















Reviews: