background image

12

Function Description...

Charging the battery

The batteries are shipped discharged and must
be charged prior to first use. Locate the charger

(C)

and one of the two 7.2V batteries 

(B)

. Plug

the charger into the mains and switch on. The
GREEN LED indicator will light up. Insert the
battery 

(B)

into the charger, 

NOTE MAKE SURE

THE BATTERY IS IN THE CORRECT 
ORIENTATION IN THE CHARGER. 

(See figs 1

and 2) The RED LED will start flashing and charg-
ing will commence. Charging time will take

approximately three hours. When charging is
complete both LED indicators will stay on.
Disconnect the 
battery charger 

(C)

from the mains and remove

the battery 

(B)

from the charger.

NOTE: Over usage such as over-charge, 
 over-discharge and high temperatures will
result in a short  life span. To avoid this the
batteries should be charged and discharged
once every three months.

Fig 1

Fig 2

Installing or removing the battery

!

B

C

RED LED

FLASHING

GREEN LED

Hold the battery 

(B)

so the lock button is on top.

Inset the battery into the installment opening to
the rear of the nailer 

(A)

, see fig 3 and insert   it in

until it clicks home.

WARNING DO NOT USE FORCE

when

inserting the battery cartridge. If it does not slide
in easily, it is not being inserted correctly.

To remove the battery 

(B)

, press down the lock

button and pull the battery back.

Fig 3

Fig 4

A

B

Fuel cell

Remove the cap 

(2)

, push in the metering valve

front edge 

(1)

then push in the back edge until it

seats. (See fig 4)

1)

Metering valve

2)

Cap

2

1

1

Front

edge

Back

edge

Attaching the metering valve to the fuel cell

Summary of Contents for GFN3490

























Reviews: