background image

 

 
 

 

 
For your own safety, read instruction manual before operating the machine. Learn 
the machine’s application and limitations as well as the specific hazards peculiar. 

 

Always wear approved safety glasses or a face shield when operating or observing 
machinery to reduce the risk of eye injury or blindness from flying particles everyday. 
Eyeglasses are not approved safety glasses. 

 

Dust created while usingmachinery may cause cancer, birth defects, or long-term 
respiratory damage. Be aware of dust hazards associated with each workpiece 
material, and always wear an approved respirator to reduce your risk. 

 

Always wear hearing protection when operating or observing loud machinery. 
Extended exposure to this noise without hearing protection can cause permanent 
hearing loss. 
 

 

Keep hands and clothing away from moving parts. Always tie back or cover long hair. 
Wear non-slip footwear to avoid accidental slips which could cause a loss of 
workpiece control. 

 

1.11 Personal protective equipment   

 

 

 
Dirty or contaminated personal protective equipment can cause illness. Clean your 
personal protective equipment after each use and once a week. 
 

1.2 Safety instructions for dust collector 

Long-term respiratory damage can occur from using dust collectors without proper 
use of a respirator. Fire or explosions can result in smoke inhalation, serious burns, 
or death—if machine is used to collect incorrect materials, is operated near 

potential explosion sources, or ducting is improperly grounded. Entanglement, amputation, or 
death can occur if hair, clothing, or fingers are pulled into the inlet. To reduce the risk of these 
hazards, operator and bystanders MUST completely heed the hazards and warnings below. 

 
 

protective suit 

safety shoes 

protective gloves 

protective glasses 

 

 

 

 

Summary of Contents for 107698

































Reviews: