AXIOMATIC AX140900 User Manual Download Page 9 | Manualshive

Page: 9 / 36

background image

UMAX140900. Ethernet to CAN Converter. Version 5

Page: 9-35

2.3.2 Web Server

The

Web Server

provides a user front-end interface with the converter. It runs a dynamic

website that shows: the converter general information, configuration parameters, and the
converter real-time diagnostics.

The user can also change configuration parameters and upload the new firmware through this
website.

The web browser should support JavaScript.

2.3.3 Firmware Updates

Starting from version 5.xx, the firmware can be remotely updated through the web server.

2.3.4 Network Discovery

Starting from version 5.xx, the firmware supports a proprietary Axiomatic discovery protocol. It
allows to locate a converter with unknown IP address and/or web server port on a LAN using a
simple Axiomatic discovery application

AxioDisc.exe

.

«
...
7
8
9
10
11
...
»

Summary of Contents for AX140900





































Reviews:

No comments

Related manuals for AX140900

Brand: Daewoo Pages: 36

Brand: RGBlink Pages: 13

Brand: DAB PUMPS Pages: 635

OSD2166M Series

Brand: Optical Systems Design Pages: 16

COMMAND VALVE P1012593

Brand: Ideal Vacuum Pages: 9

PROFINET Master HD67B70-232-A1

Brand: ADF Web Pages: 31

Brand: Envertech Pages: 2

Brand: CYP Pages: 23

Brand: Wolverine Pages: 14

Brand: Sovereign Pages: 4

Brand: PhD Solutions Pages: 14

Brand: Mayty Pages: 14

Brand: Commax Pages: 11

Pro Convert AES67

Brand: Magewell Pages: 67

Brand: Haier Pages: 49

Brand: OXO Pages: 16

Brand: KTI Networks Pages: 25

Brand: CYP Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands